تعیین مسیر فشار بهینه در فرآیند هیدروفرمینگ ورق بااستفاده از روش تبرید تدریجی

نوع مقاله : مقاله کوتاه

نویسندگان

1 دانشگاه تربیت دبیر شهید رجایی

2 دانشگاه بیرجند

چکیده

در فرآیندهای شکل دهی ورق، تولید قطعات مخروطی-استوانه ای در یک مرحله و با دقت بالا به‌دلیل وجود عیوب چروکیدگی و پارگی بسیار دشوار است. یکی از کاراترین روش ها در میان فرآیندهای هیدروفرمینگ ورق به‌منظور تولید قطعات مخروطی- استوانه ای، روش کشش عمیق هیدرودینامیکی با فشار شعاعی است. در این مقاله مسیر فشار شکل دهی به‌عنوان یکی از مهم‌ترین پارامترهای مؤثر در این فرآیند، مورد بررسی قرار گرفت و در یک روش جدید با ترکیب روش اجزای محدود با استفاده از نرم‌افزار انسیس و بهینه‌سازی با الگوریتم تبرید تدریجی، مسیر بهینۀ فشار به‌دست آمد.

کلیدواژه‌ها


عنوان مقاله [English]

Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method

نویسندگان [English]

  • Abbas Hashemi 1
  • Mohammad Hoseinpour 1
  • Seyed Mohammad Hossein Seyedkashi 2
1 دانشگاه تربیت دبیر شهید رجایی
2 University of Birjand
چکیده [English]

In sheet metal forming processes, one-stage production of conical-cylindrical parts with high accuracy is very difficult due to wrinkling and rupturing. Hydrodynamic deep drawing assisted by radial pressure is one of the most applicable procedures in sheet hydroforming process on the point of producing conical-cylindrical parts. In this paper, forming pressure path is investigated as one of the most important parameters of this process. The optimized pressure path is obtained utilizing a new procedure by combination of the finite element method using ANSYS/LS-DYNA and an optimization method using simulated annealing.

کلیدواژه‌ها [English]

  • Conical-Cylindrical Parts
  • Hydrodynamic deep drawing
  • Simulated Annealing Algorithm
  • Finite Element Code
  • Pressure path
1. Hashemi, A., Mashhadi, M., Bakhshi Jooybari, M. and Gorji, A., "Study of the effect of material properties and sheet thickness on formability of conical parts in hydro-mechanical deep drawing assisted by radial pressure", Advanced Materials Research, Vol. 445, pp. 149-154, (2012).
2. Lang, L., Danckert, J. and Nielsen, K.B., "Study on hydromechanical deep drawing with uniform pressure onto the blank", Int. J. Machine Tools & Manufacture, Vol. 44, pp. 495–502, (2004).
3. Thiruvarudchelvan, S. and Lewis, W., "A note on hydroforming with constant fluid pressur", J. Materials Processing Technology, Vol. 88, pp. 51–56, (1999).
4. Zhang, S.H., Wang, Z.R., Xu, Y., Wang, Z.T. and Zhou, L.X., "Recent developments in sheet hydroforming technology", J. Materials Processing Technology, Vol. 151, pp. 237–241, (2004).
5. Lang, L.H., Wang, Z.R., Kang, D.C., Yuan, S.J., Zhang, S.H., Danckert, J. and Nielsen, K.B., "Hydroforming highlights: sheet hydroforming and tube hydroforming", J. Materials Processing Technology, Vol. 151, pp. 165–177, (2004).
6. Thiruvarudchelvan, S. and Travis, F.W., "Hydraulic pressure enhanced cup drawing processes an appraisal", J. Materials Processing Technology, Vol. 140, pp. 70–75, (2003).
7. Lang, L. and Danckert, J., "Investigation into hydrodynamic deep drawing assisted by radial pressure Part I. Experimental observations of the forming process of aluminum alloy", J. Materials Processing Technology, Vol. 148, pp. 119–131, (2004).
8. Khandeparkar, T. and Liewald, M., "Hydromechanical deep drawing of cups with stepped geometries", J. Materials Processing Technology, Vol. 202, pp. 246-254, (2008).
9. Lang, L., Danckert, J. and Nielsen, K.B., "Investigation into hydrodynamic deep drawing assisted by radial pressure Part II. Numerical analysis of the drawing mechanism and the process parameters", J. Materials Processing Technology, Vol. 166, pp. 150-161, (2005).
10. Palaniswamy, H., Ngaile, G. and Altan, T., "Optimization of blank dimensions to reduce springback in the flexforming process", J. Materials Processing Technology, Vol. 146, pp. 28–34, (2004).
11. Lang, L., Li, T., Zhou, X., Kristensen, B.E., Danckert, J. and Nielsen, K.B., "Optimized decision of the exact material modes in the simulationfor the innovative sheet hydroforming method", J. Materials Processing Technology, Vol. 177, pp. 692–696, (2006).
12. Choi, H., Koc, M. and Ni, J., "Determination of optimal loading profiles in warm hydroforming of lightweight materials", J. Materials Processing Technology, Vol. 190, pp. 230–242, (2007).
13. Yaghoobi, A., Baseri, H., Bakhshi-Jooybari, M., Gori, A., "Optimization of Pressure Path in Sheet Hydroforming Process Using Artificial Intelligence and Simulated Annealing", Advanced Materials Research, Vol. 622, pp. 772-779, (2014).
14. Liu, X., Xu, Y. and Yuan, Sh., "Effects of Loading Paths on Hydrodynamic Deep Drawing with Independent Radial Hydraulic Pressure of Aluminum Alloy Based on Numerical Simulation", J. Material Science and Technology, Vol. 24, pp. 395-399, (2008).
15. Kirkpatrick, S., Gelatt, C.D. andVecchi, M.P., "Optimization by Simulated Annealing", Science,Vol. 220, pp. 671-680, (1983).
16. Metropolis, N., Rosenbluth, A., Rosenbluth, M., Teller, A. and Teller, E., "Equation of state calculations by fast computing machines", J. Chemical Physics, Vol. 21, pp. 1087-1092, (1953).
17. Yang, X.Sh., "Nature-Inspired Optimization Algorithms", pp. 67–75, Elsevier, (2014).
18. Seyedkashi, S.M.H., Moslemi Naeini, H., Liaghat, G.H., Mosavi Mashhadi, M. and Moon, Y.H., "Numerical and experimental study on the effect of expansion ratio, corner fillets and strain rate in warm hydroforming of aluminium tubes", Modares Mechanical Engineering, Vol. 12, No. 5, pp. 122-131, (2012). (In Persian)
19. Mirzaali, M., Seyedkashi, S.M.H., Liaghat, G.H., Moslemi Naeini, H., Shojaee, K. and Moon, Y.H., "Application of simulated annealing method to pressure and force loading optimization in tube hydroforming process", Int. J. Mechanical Sciences, Vol. 55, pp. 78–84, (2012).
20. Papadia, G., Del Prete, A., Spagnolo, A. and Anglani, A., "Pre-Bulging influence on an inverse drawn shape obtained with Hydromechanical Deep Drawing(HDD)", Int. J. Material Forming, Vol. 3, pp. 287- 290, (2010).
21. Seyedkashi, S.M.H., Moslemi Naeini, H., Liaghat, G.H., Mosavi Mashhadi, M., Mirzaali, M., Shojaee, K. and Moon, Y.H., "The effect of tube dimensions on optimized pressure and force loading paths in tube hydroforming process", J. Mechanical Sciences and Technology, Vol. 26, No.6, pp. 1817–1822, (2012).
22. Seyedkashi, S.M.H., Moslemi Naeini, H., Liaghat, G.H., Mosavi Mashadi, M., Shojaee Ghandashtani, K., Mirzaali, M. and Moon, Y.H., "Experimental and Numerical Investigation of Simulated Annealing Technique in Optimization of Warm Tube Hydroforming, Proceedings of the Institution of Mechanical Engineers", Part B, J. Engineering Manufacture, Vol. 226, No.11, pp. 1869–1879, (2012).
CAPTCHA Image