Journal Of Applied and Computational Sciences in Mechanics

Keyword Index

A

ABAQUS Theoretical and Experimental Thermal Post Buckling Analysis of Columns [Volume 26, Issue 2, 2015, Pages 129-140]
ABS Investigating the mechanical properties of polymer composite materials made by 3D printing method [Volume 35, Issue 4, 2023, Pages 77-89]
Absorption refrigeration Evaluation of an integrated solar-geothermal energy system to provide power, heat and cooling [Volume 34, Issue 4, 2022, Pages 19-34]
Accelerated turbulent flow Accelerated Turbulent Pipe Flow Study using Various Turbulence Models [Volume 27, Issue 2, 2016, Pages 11-28]
Acoustic Emission Study of the Effect of Machining Parameters on Drilling of Composite Materials and Monitoring of Process by Acoustic Emission [Volume 24, Issue 2, 2012, Pages 1-16]
Acoustophoresis Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
Active controller Investigation of the impact of blowing jet on the dynamic stall of NACA0012 [Volume 34, Issue 1, 2022, Pages 1-20]
Active flow control Investigation of Suction Jet Parameters in Flow Control of Dynamic Stall [Volume 32, Issue 2, 2020-2021, Pages 181-200]
Actuator Disk Simulation of Flow Field around a Generic Helicopter Fuselage by Modeling the Rotor [Volume 25, Issue 1, 2013, Pages 1-16]
Actuator saturation Fixed-time Fault Tolerant Control Based on Neural Network and Adaptive Sliding Mode Controller of Autonomous Underwater Vehicle with Actuator Saturation [(Articles in Press)]
ADAMS Software The Effects of Revolute Joint Clearance on the Kinematic Behavior of the 3RPR Planar Parallel Manipulator [Volume 31, Issue 1, 2020, Pages 39-52]
Adaptive dynamic fast terminal sliding mode controller Fixed-time Fault Tolerant Control Based on Neural Network and Adaptive Sliding Mode Controller of Autonomous Underwater Vehicle with Actuator Saturation [(Articles in Press)]
Adaptive Time Spectral Method Application of Adaptive Time Spectral Method to Analyze Inviscid Compressible Flow Around a Pitching Airfoil [Volume 35, Issue 1, 2023, Pages 1-18]
Added Mass Calculating the Added Mass Matrix of an Airship Using Boundary Element Method [Volume 34, Issue 2, 2022, Pages 15-28]
Adsorbent Numerical and Experimental Investigation on the Parabolic Dish SolarConcentrator [Volume 32, Issue 1, 2020-2021, Pages 17-38]
Aerodynamic Numerical and Experimental Investigation of Aerodynamic of Quadrotor Blades in low Reynolds [Volume 27, Issue 1, 2016, Pages 135-152]
Aerodynamic Coefficient Aerodynamic Performance Investigation of an Experimental Variable-Span Morphing Wing Model [Volume 27, Issue 1, 2016, Pages 35-50]
Aerodynamic Optimization Numerical Study of Improving the Aerodynamic Performance of the High Lift Devices in the Two-Element Airfoil [Volume 35, Issue 1, 2023, Pages 37-52]
Aerodynamic Shape Optimization Introduction of Harmony Search Algorithm for Aerodynamic Shape Optimization Using the Navier-Stokes Equations [Volume 24, Issue 2, 2012, Pages 81-96]
Aerodynamics performance Investigation of Suction Jet Parameters in Flow Control of Dynamic Stall [Volume 32, Issue 2, 2020-2021, Pages 181-200]
Aerodynamics performance Investigation of the impact of blowing jet on the dynamic stall of NACA0012 [Volume 34, Issue 1, 2022, Pages 1-20]
Airship Calculating the Added Mass Matrix of an Airship Using Boundary Element Method [Volume 34, Issue 2, 2022, Pages 15-28]
Airstream Experiments on the Formation Process of Bag Breakup Regime of Injected Liquid Jet into an Airstream [Volume 31, Issue 2, 2020, Pages 1-18]
Al2024-T6 Vibration drilling tool and thrust force investigation in vibratory drilling process of Al 2024-T6 [Volume 26, Issue 1, 2015, Pages 129-142]
Aligned cooling towers Thermal Performance Analysis of Natural Draft Dry Cooling Towers Based on New Theoretical Method [Volume 32, Issue 1, 2020-2021, Pages 191-210]
Aluminum 5083 Experimental and Numerical Study on Aluminum Damage Using a Nonlinear Model of Continuum Damage Mechanics [Volume 27, Issue 2, 2016, Pages 41-54]
Aluminum foam Numerical study of the effect of geometry and metal foam on the energy absorption of nested profiles [Volume 34, Issue 3, 2022, Pages 67-78]
Aluminum seamless pressure vessel Feed effect on strain and stress in dome forming (spinning) of a tube in an aluminum CNG vessel manufacturing [Volume 32, Issue 2, 2020-2021, Pages 43-60]
Aluminum sheet Experimental and Numerical Analysis of Single and Double layered Aluminum Sheet 3105 With Mechanical Joints under Drop Weight Impact [Volume 30, Issue 2, 2018, Pages 109-123]
Amplification factor Effects of Divergence Angle on Moveable Nozzle Performance in Thrust Vector Control System [Volume 26, Issue 1, 2015, Pages 1-15]
Analysis of variance Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel [Volume 23, Issue 2, 2012, Pages 99-110]
Analysis of variance Analysis of Forming Parameters in Sheet Hydro-Forming Process [Volume 24, Issue 1, 2012, Pages 33-52]
Analytical Solution A Study of the Effect of Curvature of the Corner of Hole on Stress Concentration Caused by Uniform Heat Flux [Volume 28, Issue 1, 2017, Pages 63-74]
Analytical Solution Analytical Modeling of a Counterflow Diffusion Flame of a Dust Cloud [Volume 28, Issue 1, 2017, Pages 93-110]
Analytical Solution The Effect of Equilibrium Equation and Trefftz Functions on the Responses of Quadrilateral Bending Plate [Volume 29, Issue 2, 2017, Pages 99-118]
Anderson-Darling and Chi Squared The Friction Factor of Turbulent Flow of the Base Fluid and Nanofluid in the Statistical Approach [Volume 31, Issue 1, 2020, Pages 105-122]
Angle control Beyond Pull-in Stabilization of a 2-DOF Torsional Micro-Actuator using a Fuzzy Controller [Volume 27, Issue 2, 2016, Pages 99-112]
Angle-ply Laminate Free vibration analysis of sandwich panel plate with FML face sheet and flexible core using third-order shear deformation theory [Volume 34, Issue 4, 2022, Pages 1-18]
Angular Deviation Theoretical and Experimental Investigation on the Vehicle Lateral Deviation Due to the Braking Force Error [Volume 23, Issue 1, 2012, Pages 41-52]
Angular Velocity Dynamics Modeling and Analysis a New Mechanism for Automatic Control of Angular Velocity of a Rotary Axis [Volume 26, Issue 2, 2015, Pages 1-13]
An inclined enclosure Calculation of Surface Radiation Entropy Generation by Developing the Net Radiation Method in an Inclined Enclosure with Natural Convection [(Articles in Press)]
Annular Plasma Synthetic Jet Actuator Introduction of a Modified Phenomenological Model for Single and Annular Plasma Synthetic Jet Actuators [Volume 35, Issue 4, 2023, Pages 91-106]
API X65 microalloyed steel Investigation of Chemical Composition Influence on Mechanical Properties of API X65 Microalloyed Steel [Volume 23, Issue 2, 2012, Pages 47-64]
API X65 steel Effect of V-notch Depth on Fracture Toughness and the Plastic Region of the Crack Tip Using Charpy Impact Test Data in API X65 Steel [Volume 31, Issue 2, 2020, Pages 19-32]
API X70 Experimental Determination of Residual Stresses in Multi-Pass Girth Welding of Thermo-Mechanical Steel Pipe [Volume 25, Issue 2, 2013, Pages 111-120]
Artificial Bee Colony Algorithm Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell [(Articles in Press)]
Artificial neural network Damage Identification of Cylindrical Shells Based on Mode Shapes Curvature [Volume 30, Issue 1, 2018, Pages 119-128]
Artificial neural network Optimal Design of Divergent Part of an Over-expanded Nozzle Profile using Artificial Intelligence [Volume 35, Issue 1, 2023, Pages 19-36]
Artificial neural network Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell [(Articles in Press)]
Artificial neural networks A New Hybrid Strategy for Forward Kinematic Analysis of Parallel Robots [Volume 27, Issue 1, 2016, Pages 163-172]
Aspect Ratio Study of Wing Shapes Influence on MAV Aerodynamic Coefficients [Volume 23, Issue 2, 2012, Pages 29-46]
Asymmetrical-channel section Geometry Effects of Asymmetrical Channel Sections on Common Defects in the Roll Forming Process [Volume 30, Issue 2, 2018, Pages 1-16]
Asymmetric thermal flux Numerical simulation of turbulent heat transfer in boiler with supercritical fluid and asymmetric thermal conditions [(Articles in Press)]
Atomic force microscope Experimental and Theoretical Investigation of Young's Modulus of Breast Cancer Tissue (MCF-10) Using Different Cantilevers of Atomic Force Microscope [Volume 36, Issue 1, 2024, Pages 61-76]
Atomic force microscope Using new friction models to investigate the mechanical properties of liver cancer tissue [(Articles in Press)]
Atomic Force Microscopy Experimental Determination of HT29 Cancerous Cell Surface Roughness by Atomic Force Microscopy to be Applied in Nanomanipulation [Volume 28, Issue 1, 2017, Pages 111-122]
Atomic Force Microscopy Investigation of New Friction Models in Two-Dimensional Manipulation of Gastric Cancer Tissue [Volume 35, Issue 2, 2023, Pages 1-16]
Atomic Force Microscopy Manipulation of breast cell tissue with the aim of calculating Young's modulus, using Tatara contact theory and atomic force microscopy [Volume 35, Issue 3, 2023, Pages 1-16]
Atomic Force Microscopy Investigating the effect of HK friction model input parameters on the force and critical time in gold nanoparticle manipulation [Volume 35, Issue 4, 2023, Pages 1-16]
Automatic Control Dynamics Modeling and Analysis a New Mechanism for Automatic Control of Angular Velocity of a Rotary Axis [Volume 26, Issue 2, 2015, Pages 1-13]
Autonomous underwater vehicle Fixed-time Fault Tolerant Control Based on Neural Network and Adaptive Sliding Mode Controller of Autonomous Underwater Vehicle with Actuator Saturation [(Articles in Press)]
Axial Gap Experimental and Numerical Study of Partial Admission Effect on Flow Distribution in Supersonic Turbine Axial-Gap [Volume 24, Issue 2, 2012, Pages 17-32]
Axial Load Effect of Piezoelectric Patches on the Vibration and Buckling of Euler-Bernoulli Beams under Axial Load [Volume 27, Issue 2, 2016, Pages 29-40]
Axisymmetric Problems Effect of Superconvergent Stress Points for Solution Improvement and Error Estimation of Isogeometric Analysis of Axisymmetric Problems [Volume 26, Issue 1, 2015, Pages 79-95]

B

Bag Breakup Regime Experiments on the Formation Process of Bag Breakup Regime of Injected Liquid Jet into an Airstream [Volume 31, Issue 2, 2020, Pages 1-18]
Baldwin-Lomax method .Numerical Modelling of Water Hammer Problems based on the Flux Wave Approach and Baldwin-Lomax Turbulence Model [Volume 29, Issue 1, 2017, Pages 97-110]
Baldwin-Lomax turbulence model Periodic Unsteady Transonic Compressible Flow Simulation using Fourier-Based Algorithm [Volume 25, Issue 2, 2013, Pages 47-64]
Ball Burnishing Study on the effects of ball burnishing parameters and initial surface roughness on the core roughness characteristics of Copper cylindrical parts [Volume 32, Issue 2, 2020-2021, Pages 113-132]
Ball valves Numerical Simulation of Gas Flow inside the Orbit Valve Class 900 and its Effects on Parts Damages [Volume 30, Issue 2, 2018, Pages 125-136]
Battery bank Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Beam nonlinear analysis Nonlinear Bending Analysis of Nanocomposite Beams Reinforced by Graphene Platelets using Harmonic Differential Quadrature Method [Volume 33, Issue 2, 2021, Pages 23-40]
Bending The effect of material degradation on the bending of laminated plates [Volume 34, Issue 2, 2022, Pages 1-14]
Bending Experimental investigation and Numerical simulation of bending parameters on the spring back of the tube in the rotational bending process [(Articles in Press)]
Bending Experimental and Numerical Investigation of Pressure-Induced Changes in Tube Thickness Distribution and Cross-Section during Rotary Bending [(Articles in Press)]
Bending angle Study of the Effect of Process Parameters and Optimization of Bending Angle in Laser Bending [Volume 36, Issue 1, 2024, Pages 1-24]
Bending collapse Bending Collapse of Thin Walled Energy Absorber and Presenting Numerical Simplified Model [Volume 26, Issue 2, 2015, Pages 119-128]
Bending plate .Variable Damping in Geometric Nonlinear Plate Bending Analysis using Dynamic Relaxation Method [Volume 28, Issue 2, 2017, Pages 115-142]
Bifurcation An investigation on the Resonances and Chaotic Behavior of a Nonlinear Vehicle Suspension System [Volume 24, Issue 1, 2012, Pages 53-70]
Bilayer Graphene Application of SSPH Method in Free Vibration Analysis of Graphene [Volume 31, Issue 2, 2020, Pages 53-66]
Bilinear stiffness model Introducing a New Crack Disturbance Function for Transverse Vibration Analysis of a Cracked Beam [Volume 25, Issue 2, 2013, Pages 19-32]
Biomass Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Biped robot Dynamic Modeling and Optimal Walking Gait Planning of a Real Biped Robot Based on SLIP and Compass gait Models [Volume 30, Issue 1, 2018, Pages 31-50]
Blade angle Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Bleiman and Sorin friction models Using new friction models to investigate the mechanical properties of liver cancer tissue [(Articles in Press)]
Bluntness A Study of the Effect of Curvature of the Corner of Hole on Stress Concentration Caused by Uniform Heat Flux [Volume 28, Issue 1, 2017, Pages 63-74]
Bone Heterogeneity Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Bonora Model Experimental and Numerical Study on Aluminum Damage Using a Nonlinear Model of Continuum Damage Mechanics [Volume 27, Issue 2, 2016, Pages 41-54]
Boundary conditions Boundary Condition Identification of a Clamped Beam in the Flexible Support [Volume 28, Issue 2, 2017, Pages 85-96]
Boundary Element Method Calculating the Added Mass Matrix of an Airship Using Boundary Element Method [Volume 34, Issue 2, 2022, Pages 15-28]
Brake Force Error Theoretical and Experimental Investigation on the Vehicle Lateral Deviation Due to the Braking Force Error [Volume 23, Issue 1, 2012, Pages 41-52]
Brake Force Error An Investigation on the Effects of Geometric and Dynamic Parameters on the Truck Lateral Deviation Due to the Braking Force Imbalance [Volume 26, Issue 2, 2015, Pages 141-152]
Brake Parachute Design Derivation of Aerodynamic Characteristics of a Ribbon Parachute by Truck Tow Test [Volume 36, Issue 1, 2024, Pages 25-40]
Broadband shock-associated noise Numerical Prediction of Near-field Noise and Return Acoustics from Sonic Jets in Different Operating Conditions [Volume 32, Issue 2, 2020-2021, Pages 19-42]
Bubbling Fluidized Bed Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Buckling Stability and Free Vibration Analysis of Plates with Random Material Property using Stochastic Finite Element Method [Volume 30, Issue 2, 2018, Pages 151-160]
Buckling Load Effect of Piezoelectric Patches on the Vibration and Buckling of Euler-Bernoulli Beams under Axial Load [Volume 27, Issue 2, 2016, Pages 29-40]
Buckling, piezoelectric Analytical Solution for Buckling of FGM Plates with Integrated Piezoelectric Layers under Open and Closed Circuit Conditions [Volume 26, Issue 2, 2015, Pages 15-31]
Bulge height Effect of Sealing Position on Bulge Height in Hydroforming of Aluminum Tubes [Volume 29, Issue 1, 2017, Pages 81-96]

C

Cage roll forming Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Cancerous tissue Manipulation of breast cell tissue with the aim of calculating Young's modulus, using Tatara contact theory and atomic force microscopy [Volume 35, Issue 3, 2023, Pages 1-16]
Cancer‌ tissue Numerical Study on the Thermal Stress caused by Laser Radiation on Healthy and Cancerous Skin Tissue [Volume 32, Issue 1, 2020-2021, Pages 59-76]
Capillary tube mass flow meter Designing and Numerical Analysis of Capillary Tube Thermal Mass Flowmeter as a Residential Natural Gas Meter [Volume 29, Issue 1, 2017, Pages 49-62]
Carbon nitride Analysis of fracture behavior of carbon nitride poly crystalline by genetic algorithm and molecular dynamics methods [(Articles in Press)]
Carbon reinforced laminated composite Numerical And Experimental Investigation of deflection of Laminated composites due to drop weight of different projectiles [Volume 33, Issue 2, 2021, Pages 41-54]
Casimir Stability Analysis of Nano-wire Made Tweezers in Magnetic Flux [Volume 32, Issue 2, 2020-2021, Pages 149-164]
CCHP systems Optimization of Combined Cooling Heating and Power System (CCHP) by a Novel Hybrid Method [Volume 30, Issue 1, 2018, Pages 61-78]
C-D Nozzle Experimental Investigation of the Influence of Transverse Dual protuberances on the Thrust Vector of a Supersonic C-D nozzle [Volume 31, Issue 1, 2020, Pages 139-154]
Cell Separation Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
Central difference method (CDM)) Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Ceramic Drying Study the Factors affecting the Moisture Diffusion Coefficient in Drying Clay Ceramics and Explanations the Analytical Model Process [Volume 27, Issue 1, 2016, Pages 87-102]
CFD Numerical Investigation of Darrieus Wind Turbine near a One-way Highway [Volume 32, Issue 1, 2020-2021, Pages 1-16]
CFD Scaling of a Radial Turbine for Turbocharger of a Lean Combustion Engine [Volume 32, Issue 2, 2020-2021, Pages 165-180]
CFD simulation Parametric study and numerical analysis of the regenerative compressor with symmetric aerodynamic blades, to improve performance [Volume 32, Issue 2, 2020-2021, Pages 1-18]
Channel Numerical and Analytical Investigation of Thermal Dispersion Effects on the Heat Transfer of Nanofluid flow inside a Channel [Volume 29, Issue 2, 2017, Pages 21-40]
Chevron plate Numerical investigation of heat transfer and pressure drop in a plate heat exchanger with Chevron plates [Volume 25, Issue 1, 2013, Pages 47-60]
Chimney Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Chirp signal Identification of electromagnetic linear motor parameters in order to generate inertial force using ARM microcontroller [Volume 34, Issue 2, 2022, Pages 87-98]
Choked nozzle Numerical Prediction of Near-field Noise and Return Acoustics from Sonic Jets in Different Operating Conditions [Volume 32, Issue 2, 2020-2021, Pages 19-42]
Circular and Noncircular Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]
Circular Cylinder Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Circular Cylinder Comparison of Single and L-PSJ DBD Plasma Actuators for Flow Control around a Cylinder [Volume 30, Issue 2, 2018, Pages 137-149]
Circular Cylinder Numerical Simulation of the Heat-Fluid Flow Behavior Around the Cylinder with the Controller Wire [Volume 31, Issue 2, 2020, Pages 105-126]
Circular-square Bending Collapse of Thin Walled Energy Absorber and Presenting Numerical Simplified Model [Volume 26, Issue 2, 2015, Pages 119-128]
Climate change Estimation of solar radiation in different climates of Iran using hybrid machine learning methods [Volume 35, Issue 2, 2023, Pages 37-54]
Closed-cell aluminium foam Experimental Investigation on Process Parameters Effects in Laser Forming of Closed-cell Aluminium Foam Sheets [Volume 26, Issue 2, 2015, Pages 33-44]
CNC Milling Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
CNC Parametric Interpolation Look-Ahead NURBS-PH Interpolators for High Speed CNC Milling [Volume 23, Issue 1, 2012, Pages 83-96]
CNG storage cylinder Determination of the Critical Area and Reusability of Compressed Natural Gas Storage Cylinder in Collision [Volume 25, Issue 1, 2013, Pages 29-46]
Code-Aster Finite Element Modeling of Laser Ultrasonics Process in Thermoelastic Regime [Volume 32, Issue 1, 2020-2021, Pages 133-152]
Coil pitch Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Cold cylinder Experimental Study of Wall Roughness Effects on the Frost Formation over a Cylinder [Volume 30, Issue 1, 2018, Pages 51-60]
Cold roll-forming Geometry Effects of Asymmetrical Channel Sections on Common Defects in the Roll Forming Process [Volume 30, Issue 2, 2018, Pages 1-16]
Collector thermal efficiency Thermo-Economic evaluation of a solar dryer with evacuated heat pipe collector and energy storage [Volume 32, Issue 1, 2020-2021, Pages 39-58]
Combined Cycle Multi Objective Optimization of Converting an Old Steam Power Plant to Combined Cycle Power Plant (CCPP) Using Double and Single Pressure Heat Recovery Steam Generator (HRSG) via Genetic Algorithm [Volume 27, Issue 2, 2016, Pages 129-139]
Combined fin absorber tube. Turbulator Evaluation of energy and exergy of a parabolic trough solar collector equipped with internal fin and star turbulator absorber tube [(Articles in Press)]
Combustion Investigation of Flame Location Effect on Flame Temperature in Premixed Counterflow Combustion of Particle-Cloud [Volume 26, Issue 1, 2015, Pages 119-128]
Combustion Numerical Study of the Effects of Structural and Functional Parameters on Unmixed Combustion of Natural Gas in Three Radiant Tubes with Different Geometries [Volume 33, Issue 2, 2021, Pages 83-92]
Combustion products Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Compact heat exchanger Investigating the Effect of Angle and Length of Vortex Generators with Sinusoidal Structure on Compact Heat Exchangers Performance [(Articles in Press)]
Complex Variable Method A Study of the Effect of Curvature of the Corner of Hole on Stress Concentration Caused by Uniform Heat Flux [Volume 28, Issue 1, 2017, Pages 63-74]
Composite Study of the Effect of Machining Parameters on Drilling of Composite Materials and Monitoring of Process by Acoustic Emission [Volume 24, Issue 2, 2012, Pages 1-16]
Composite Laminates Experimental Study of the Roll Forming of PVC / Glass Fabric Composite Laminates [Volume 28, Issue 2, 2017, Pages 21-34]
Composite Materials Investigating the mechanical properties of polymer composite materials made by 3D printing method [Volume 35, Issue 4, 2023, Pages 77-89]
Compressible materials Solution of Nonlinear Compressible Hyperelastic Problems by Isogeometric Analysis Method [Volume 30, Issue 2, 2018, Pages 67-82]
Compressor Optimization of one Stage Axial Compressor by using Quasi-Three Dimensional Design and Hybrid Genetic Algorithm [Volume 26, Issue 1, 2015, Pages 63-78]
Computational modeling Modeling and Simulation of Growth in Diastolic Heart Failure [Volume 35, Issue 3, 2023, Pages 101-114]
Concave Surface Numerical Simulation of the Effects of Sinusoidal Pulsed Impinging Jet on Heat Transfer from the Concave Cylindrical Surface [Volume 29, Issue 1, 2017, Pages 17-30]
Condensing flows Investigation of The Effects of Coalescence on The Wet Steam Flows [Volume 26, Issue 1, 2015, Pages 51-62]
Condition monitoring Automated Fault Detection of Tri-Lobe Compressor Using Wavelet Transformation and Support Vector Machine [Volume 27, Issue 1, 2016, Pages 19-34]
Conformal Mapping Study of Unsteady Viscous Turbulent Flow with High Reynolds Passing One, Two & Three Cylinders by Random Vortex Method (RVM) [Volume 24, Issue 1, 2012, Pages 133-146]
Conformal Mapping A Study of the Effect of Curvature of the Corner of Hole on Stress Concentration Caused by Uniform Heat Flux [Volume 28, Issue 1, 2017, Pages 63-74]
Conformal Transformation Schwarz-Christoffel Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
Conical-Cylindrical Parts Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method [Volume 28, Issue 1, 2017, Pages 123-131]
Conjugate Gradient Method Simultaneous Estimation of Location and Strength of a Heat Source in a Functionally Graded Plate by Inverse Analysis [Volume 29, Issue 2, 2017, Pages 71-88]
Conjugate heat transfer Conjugate Heat Transfer in Closed Cavity with Porous Blocks [Volume 29, Issue 1, 2017, Pages 111-121]
Conjugate heat transfer Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Conjugate heat transfer Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
Consistent couple stress theory Stability Analysis of Nano-wire Made Tweezers in Magnetic Flux [Volume 32, Issue 2, 2020-2021, Pages 149-164]
Constant angular velocity Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Contact resistance Investigating the Effect of Film in SSRSW of Hastelloy X Superalloy [Volume 30, Issue 1, 2018, Pages 129-140]
Continuous blowing jet Investigation of the impact of blowing jet on the dynamic stall of NACA0012 [Volume 34, Issue 1, 2022, Pages 1-20]
Continuum damage mechanic Prediction of High Cycle Fatigue Life with Variable Loading Amplitude using Thermography Method [(Articles in Press)]
Continuum Damage Mechanics Experimental and Numerical Study on Aluminum Damage Using a Nonlinear Model of Continuum Damage Mechanics [Volume 27, Issue 2, 2016, Pages 41-54]
Control Parameterization An Improved Shooting Method for a Class of Switching Optimal Control Problems [Volume 31, Issue 1, 2020, Pages 123-138]
Convection heat transfer Study of entropy generation and evaluation statistical heat transfer properties in turbulent flow [Volume 29, Issue 1, 2017, Pages 63-80]
Convection heat transfer Numerical investigation of the influence of the geometrical shape of the absorber of a single-slope solar desalination device [(Articles in Press)]
Convergence criterion .Variable Damping in Geometric Nonlinear Plate Bending Analysis using Dynamic Relaxation Method [Volume 28, Issue 2, 2017, Pages 115-142]
Convergence Rate Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Core Roughness Study on the effects of ball burnishing parameters and initial surface roughness on the core roughness characteristics of Copper cylindrical parts [Volume 32, Issue 2, 2020-2021, Pages 113-132]
Correlation Reliability Analysis of Beams with both Random Material Properties and Random Loading Conditions [Volume 24, Issue 1, 2012, Pages 1-18]
Correlation Presenting a Correlation to Obtain Natural Gas Leakage Rate from a Buried High-Pressure Pipeline in a Porous Media [Volume 32, Issue 1, 2020-2021, Pages 231-254]
Counterflow Investigation of Flame Location Effect on Flame Temperature in Premixed Counterflow Combustion of Particle-Cloud [Volume 26, Issue 1, 2015, Pages 119-128]
Counterflow Analytical Modeling of a Counterflow Diffusion Flame of a Dust Cloud [Volume 28, Issue 1, 2017, Pages 93-110]
Counterflow Flames The Numerical Study of Extinction Limits and Structure of H2/O2 Counterflow Diffusion Flame with Ar and He Dilution [Volume 24, Issue 2, 2012, Pages 57-66]
Coupling Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Crack Detection A Novel Method to Improve Crack Detection Ability in Helical Gear [Volume 31, Issue 1, 2020, Pages 1-12]
Cracked beam Introducing a New Crack Disturbance Function for Transverse Vibration Analysis of a Cracked Beam [Volume 25, Issue 2, 2013, Pages 19-32]
Crack Growth Numerical Simulation of Crack Growth in the Glass Layer of Gallium-Arsenide Solar Cell [Volume 33, Issue 2, 2021, Pages 93-104]
Crack Growth Criteria Evaluation of Crack Growth Criteria in Functionally Graded Polymer using Finite Element Metho [Volume 28, Issue 2, 2017, Pages 35-50]
Crack tip plastic region Effect of V-notch Depth on Fracture Toughness and the Plastic Region of the Crack Tip Using Charpy Impact Test Data in API X65 Steel [Volume 31, Issue 2, 2020, Pages 19-32]
Crack Tip Plastic Zone The Effect of Fatigue Crack Growth on Mechanical Residual Stress Redistribution [Volume 27, Issue 2, 2016, Pages 1-10]
Crash Bending Collapse of Thin Walled Energy Absorber and Presenting Numerical Simplified Model [Volume 26, Issue 2, 2015, Pages 119-128]
Crookes radiometer An Experimental Study of Crookes Radiometer [Volume 33, Issue 1, 2021, Pages 17-34]
Cubic shell Investigation of Cyclic Behavior of SS316L Cubic Shells under Pure Torsional Load [Volume 30, Issue 2, 2018, Pages 33-46]
Curing Time Simulation of Rubber Vulcanization for Calculation of the Curing Time with Modification of the Kinetic Model [Volume 26, Issue 2, 2015, Pages 107-118]
Curvature Mode Shape Damage Identification of Cylindrical Shells Based on Mode Shapes Curvature [Volume 30, Issue 1, 2018, Pages 119-128]
Curvature ratio Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Cutting Edges Number Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
Cyclic Reduction algorithm Parallel Thomas Approach in Computational Fluid Dynamics with GPUs- Lid-driven Cavity [Volume 28, Issue 2, 2017, Pages 152-164]
Cylindrical Shell Damage Identification of Cylindrical Shells Based on Mode Shapes Curvature [Volume 30, Issue 1, 2018, Pages 119-128]

D

Dagger cantilevers Experimental and Theoretical Investigation of Young's Modulus of Breast Cancer Tissue (MCF-10) Using Different Cantilevers of Atomic Force Microscope [Volume 36, Issue 1, 2024, Pages 61-76]
Dahl friction model Using new friction models to investigate the mechanical properties of liver cancer tissue [(Articles in Press)]
Damage Index Damage Identification of Cylindrical Shells Based on Mode Shapes Curvature [Volume 30, Issue 1, 2018, Pages 119-128]
Damage Index Prediction of High Cycle Fatigue Life with Variable Loading Amplitude using Thermography Method [(Articles in Press)]
Damage Mechanics Determination of the Critical Area and Reusability of Compressed Natural Gas Storage Cylinder in Collision [Volume 25, Issue 1, 2013, Pages 29-46]
Damping .Variable Damping in Geometric Nonlinear Plate Bending Analysis using Dynamic Relaxation Method [Volume 28, Issue 2, 2017, Pages 115-142]
Darcy-Brinkman-Forchheimer model Heat Transfer of Nanofluid in a Channel with Magnetic Field and Porous Obstacle using the Darcy-Brinkman-Forchheimer Model in the LBM Method [Volume 32, Issue 1, 2020-2021, Pages 153-172]
Darrieus Wind Turbine Numerical Investigation of Darrieus Wind Turbine near a One-way Highway [Volume 32, Issue 1, 2020-2021, Pages 1-16]
Defect Investigation of the Effect of Geometric Defects and Temperature Changes on the Fracture Behavior of Boron Carbide Monocrystalline Structure by Molecular Dynamics [Volume 34, Issue 1, 2022, Pages 37-48]
DEFORM Optimization of Hardening Heat treatment of Oil Extraction Machine’s Cylinder Made of Stainless steel [(Articles in Press)]
Deformation length Theoretical Solution of Linear Hardening Elastic-plastic Deformation Length for a Roll Formed Channel [Volume 24, Issue 1, 2012, Pages 19-32]
Delay time Accelerated Turbulent Pipe Flow Study using Various Turbulence Models [Volume 27, Issue 2, 2016, Pages 11-28]
DesignBuilder Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
Design of Experiment Experimental Investigation on Process Parameters Effects in Laser Forming of Closed-cell Aluminium Foam Sheets [Volume 26, Issue 2, 2015, Pages 33-44]
Design of Experiment The Grafting of a Nylon Fiber Surface by a Mixture of Two Acrylic Monomers and the Evaluation of Optimum Values by using a Traditional Design of Experiment Software [Volume 31, Issue 1, 2020, Pages 39-52]
Design of Experiment Modeling of large deflection of the chromium nanobeams using design of experiments method [Volume 35, Issue 4, 2023, Pages 107-120]
Dew Point Temperature Investigating the Effect of Polymer Membrane Characteristics on the Performance of the Membrane Humidifier [Volume 35, Issue 4, 2023, Pages 17-32]
Dielectric Barrier Discharge Introduction of a Modified Phenomenological Model for Single and Annular Plasma Synthetic Jet Actuators [Volume 35, Issue 4, 2023, Pages 91-106]
Differential-Algebraic Equations A High Accuracy Method for Solving the Differential-Algebraic Equations Arising in Mechanical Systems [Volume 36, Issue 1, 2024, Pages 107-122]
Differential-Algebric Equation Dynamics Modeling and Analysis a New Mechanism for Automatic Control of Angular Velocity of a Rotary Axis [Volume 26, Issue 2, 2015, Pages 1-13]
Differential Quadrature Method Theoretical and Experimental Thermal Post Buckling Analysis of Columns [Volume 26, Issue 2, 2015, Pages 129-140]
Differential Transform Method Free Vibration Analysis of Functionally Graded Rotating Double Tapered Beam by using Euler-bernoulli Beam Theory and Differential Transform Method [Volume 27, Issue 1, 2016, Pages 51-70]
Diffusion Flame Analytical Modeling of a Counterflow Diffusion Flame of a Dust Cloud [Volume 28, Issue 1, 2017, Pages 93-110]
Diffusion Flames The Numerical Study of Extinction Limits and Structure of H2/O2 Counterflow Diffusion Flame with Ar and He Dilution [Volume 24, Issue 2, 2012, Pages 57-66]
Diluent The Numerical Study of Extinction Limits and Structure of H2/O2 Counterflow Diffusion Flame with Ar and He Dilution [Volume 24, Issue 2, 2012, Pages 57-66]
Dimensional Accuracy Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Dipole Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
Direct Adaptive Feedback Linearization Control Variable-Pitch Control of a Quadrotor Using Feedback Linearization Controller and Direct Adaptive Feedback Linearization Controller [Volume 31, Issue 2, 2020, Pages 67-90]
Directional Illumination Thermal Radiation Heat Transfer Effects on Single Fuel Droplet Heat up Considering it’s Internal Circulation [Volume 23, Issue 1, 2012, Pages 67-82]
Direct Numerical Simulation Direct Numerical Simulation of Supersonic and Transonic Compressible Viscous Flow by Kinetic Energy Preserving Scheme [Volume 28, Issue 1, 2017, Pages 15-30]
Direct Numerical Simulation Simulation of Particle Motion in Non-Newtonian Fluids by Immersed Boundary Lattice Boltzmann Method [Volume 28, Issue 1, 2017, Pages 75-92]
Discharge coefficient Numerical Analysis of Fuel Injection Impacts on Thrust-Vectoring in a Dual Throat Nozzle [Volume 33, Issue 1, 2021, Pages 71-92]
Discrete Fourier transform Periodic Unsteady Transonic Compressible Flow Simulation using Fourier-Based Algorithm [Volume 25, Issue 2, 2013, Pages 47-64]
Discrete phase Umerical Simulation of Elbow Erosion with Circumferential Welding in Two-Phase Gas Flow [Volume 31, Issue 2, 2020, Pages 141-156]
Dissipated energy in each cycle Prediction of High Cycle Fatigue Life with Variable Loading Amplitude using Thermography Method [(Articles in Press)]
Distributed Patch Mass Vibration of FGM Plates With Distributed Mass Using Third Order Shear Deformation Theory [Volume 26, Issue 2, 2015, Pages 55-71]
Disturbance function Introducing a New Crack Disturbance Function for Transverse Vibration Analysis of a Cracked Beam [Volume 25, Issue 2, 2013, Pages 19-32]
Disturbance Torque Nonlinear Control of Motion of A Spherical Robot on Inclined Surfaces Based on Feedback Linearization Method [Volume 31, Issue 2, 2020, Pages 91-104]
Divergence Angle Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
DOE Superficial Hardening of AISI1045 Steel in High Efficiency Deep Grinding Through Optimization Approaches, Taguchi Method and SA Algorithm [Volume 24, Issue 1, 2012, Pages 87-102]
Dome forming Feed effect on strain and stress in dome forming (spinning) of a tube in an aluminum CNG vessel manufacturing [Volume 32, Issue 2, 2020-2021, Pages 43-60]
Double- helical gear Effects of Gyroscopic Moment on the Dynamics and Vibrations of a High- Speed Double- Helical Gear Pair [Volume 29, Issue 1, 2017, Pages 31-48]
Drag Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Drag coefficient Different Methods to Compute Force over a Cylinder by LBM [Volume 25, Issue 1, 2013, Pages 114-123]
Drag reduction Numerical Investigation of Drag Reduction Mechanism in Laminar Flow Regime using Rectangular Riblets [Volume 31, Issue 1, 2020, Pages 165-173]
Droplet diameter Numerical Simulation of Toos Power Plant Boiler to Improve its Thermal Efficiency [Volume 27, Issue 1, 2016, Pages 117-134]
Droplet Injection Thermal Radiation Heat Transfer Effects on Single Fuel Droplet Heat up Considering it’s Internal Circulation [Volume 23, Issue 1, 2012, Pages 67-82]
Dual throat nozzle Numerical Analysis of Fuel Injection Impacts on Thrust-Vectoring in a Dual Throat Nozzle [Volume 33, Issue 1, 2021, Pages 71-92]
Ductile fracture criterion Prediction of Forming Limit Curve Using Ductile Fracture Criteria in Hydrofoming of Aluminum Tubes [Volume 25, Issue 1, 2013, Pages 17-28]
Dust Cloud Combustion Analytical Modeling of a Counterflow Diffusion Flame of a Dust Cloud [Volume 28, Issue 1, 2017, Pages 93-110]
Duty cycle The Study of the Effect of Input Parameters on Material Romoval Rate, %Tool Water Ratio and Surface Roughness of AISI H13 Tool Steel in the Electrical Discharge Machining (EDM) [Volume 24, Issue 1, 2012, Pages 123-132]
Dynamic Implementation of Gibbs-Appell method in dynamic analysis of a novel serial-parallel hybrid robot PP-(3RSS-PS) [Volume 36, Issue 1, 2024, Pages 77-92]
Dynamic Equations Nonlinear Control of Motion of A Spherical Robot on Inclined Surfaces Based on Feedback Linearization Method [Volume 31, Issue 2, 2020, Pages 91-104]
Dynamic Mesh Improvement of Aerodynamic Performance of Oscillating Airfoils with Plunging Motion at Low Reynolds Numbers Using Heat Transfer [Volume 30, Issue 1, 2018, Pages 79-96]
Dynamic model Effects of Gyroscopic Moment on the Dynamics and Vibrations of a High- Speed Double- Helical Gear Pair [Volume 29, Issue 1, 2017, Pages 31-48]
Dynamic stall Investigation of Suction Jet Parameters in Flow Control of Dynamic Stall [Volume 32, Issue 2, 2020-2021, Pages 181-200]
Dynamic stall Investigation of the impact of blowing jet on the dynamic stall of NACA0012 [Volume 34, Issue 1, 2022, Pages 1-20]
Dynamic Stiffness The Electric Response of Piezoelectric Beam Using Dynamic Stiffness Method [Volume 31, Issue 2, 2020, Pages 127-140]

E

Edge buckling Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Edge Crack Frequency Analysis of Cracked Porous Functionally Graded Beams on Elastic Foundation using Reddy Third Order Shear Deformation Theory [Volume 32, Issue 2, 2020-2021, Pages 93-112]
Ejector pump Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Elastic-plastic material Theoretical Solution of Linear Hardening Elastic-plastic Deformation Length for a Roll Formed Channel [Volume 24, Issue 1, 2012, Pages 19-32]
Elastic plate Simulation of fluid flow in a heat exchanger with elastic intermediate separator at different working conditions [Volume 32, Issue 2, 2020-2021, Pages 77-92]
Elastohydrodynamic Investigation of Slip Condition in the Elastohydrodynamic Lubrication [(Articles in Press)]
Electric field Numerical Analysis of Magnetic Mixing Phenomenon in an Electroosmotic Flow between Two Parallel Plates [Volume 32, Issue 1, 2020-2021, Pages 174-190]
Electricity Generation Cost Multi Objective Optimization of Converting an Old Steam Power Plant to Combined Cycle Power Plant (CCPP) Using Double and Single Pressure Heat Recovery Steam Generator (HRSG) via Genetic Algorithm [Volume 27, Issue 2, 2016, Pages 129-139]
Electromagnetic actuator Identification of electromagnetic linear motor parameters in order to generate inertial force using ARM microcontroller [Volume 34, Issue 2, 2022, Pages 87-98]
Electromagnetic instability Stability Analysis of Nano-wire Made Tweezers in Magnetic Flux [Volume 32, Issue 2, 2020-2021, Pages 149-164]
Electrostatic Force Electrostatically Actuated FGM Microgripper under the Effect of Thermal Moment [Volume 23, Issue 2, 2012, Pages 65-80]
Energy absorber Bending Collapse of Thin Walled Energy Absorber and Presenting Numerical Simplified Model [Volume 26, Issue 2, 2015, Pages 119-128]
Energy absorber Study of Energy Ebsorption of Crushing Element in ER24PC Locomotive [Volume 27, Issue 1, 2016, Pages 1-18]
Energy Absorption Experimental and Numerical Analysis of Single and Double layered Aluminum Sheet 3105 With Mechanical Joints under Drop Weight Impact [Volume 30, Issue 2, 2018, Pages 109-123]
Energy Efficiency Design, construction and experimental investigation of parabolic solar cooker performance [Volume 36, Issue 1, 2024, Pages 93-106]
Energy Harvesting The Electric Response of Piezoelectric Beam Using Dynamic Stiffness Method [Volume 31, Issue 2, 2020, Pages 127-140]
Energy Optimization Investigating the effect of optimizing external skins and translucent walls on reducing energy consumption and investment return time of educational buildings in a temperate climate with dry and very hot summers [Volume 36, Issue 1, 2024, Pages 41-60]
Energy saving Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
Energy saving Feasibility of the performance of thermal photovoltaic systems in residential units in the climate of four cities of Abadan, Baghdad, Basra, and Tehran in terms of energy saving. [Volume 35, Issue 3, 2023, Pages 33-50]
Entrainment ratio Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Entropy generation Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
EPDM rubber The Study on the Mechanical Properties of the De-Vulcanized Waste Rubber by a Mechanical Technique [Volume 30, Issue 2, 2018, Pages 95-108]
Equilibrium Equations Improvement of Stress and Error Estimation by Patch Equilibrium in Isogeometric Analysisic analysis [Volume 26, Issue 2, 2015, Pages 73-87]
Equivalent Circuit A New Mathematical Model Gas Flows in Pipeline with Leak [Volume 31, Issue 1, 2020, Pages 155-164]
Erosion corrosion Umerical Simulation of Elbow Erosion with Circumferential Welding in Two-Phase Gas Flow [Volume 31, Issue 2, 2020, Pages 141-156]
Error estimation Effect of Superconvergent Stress Points for Solution Improvement and Error Estimation of Isogeometric Analysis of Axisymmetric Problems [Volume 26, Issue 1, 2015, Pages 79-95]
Error estimation Improvement of Stress and Error Estimation by Patch Equilibrium in Isogeometric Analysisic analysis [Volume 26, Issue 2, 2015, Pages 73-87]
ERW pipes Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Estimation of Heat Flux Estimation of Heat Shocks in Inverse Heat Transfer Problems using Kalman Filtering [Volume 26, Issue 2, 2015, Pages 45-54]
Euler-Bernoulli beam Effect of Piezoelectric Patches on the Vibration and Buckling of Euler-Bernoulli Beams under Axial Load [Volume 27, Issue 2, 2016, Pages 29-40]
Eulerian-Eulerian model Comparison between Single-Phase, Two-Phase Mixture and Eulerian-Eulerian Models for the Simulation of Jet Impingement of Nanofluids [Volume 27, Issue 2, 2016, Pages 55-70]
Eulerian-Lagrangian Umerical Simulation of Elbow Erosion with Circumferential Welding in Two-Phase Gas Flow [Volume 31, Issue 2, 2020, Pages 141-156]
Exergy Evaluation of an integrated solar-geothermal energy system to provide power, heat and cooling [Volume 34, Issue 4, 2022, Pages 19-34]
Exergy Evaluation of energy and exergy of a parabolic trough solar collector equipped with internal fin and star turbulator absorber tube [(Articles in Press)]
Exergy efficiency Multi Objective Optimization of Converting an Old Steam Power Plant to Combined Cycle Power Plant (CCPP) Using Double and Single Pressure Heat Recovery Steam Generator (HRSG) via Genetic Algorithm [Volume 27, Issue 2, 2016, Pages 129-139]
Exit diameter of diffuser Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Expanded metal sheet Experimental and Numerical Investigation on Concrete Specimens with Expanded Metal Sheet under Impact Loading [Volume 32, Issue 1, 2020-2021, Pages 211-230]
Experimental Aerodynamics Experimental Investigation of the Influence of Transverse Dual protuberances on the Thrust Vector of a Supersonic C-D nozzle [Volume 31, Issue 1, 2020, Pages 139-154]
Experimental Models Estimation of solar radiation in different climates of Iran using hybrid machine learning methods [Volume 35, Issue 2, 2023, Pages 37-54]
Exponential FGM Frequency Analysis of Cracked Porous Functionally Graded Beams on Elastic Foundation using Reddy Third Order Shear Deformation Theory [Volume 32, Issue 2, 2020-2021, Pages 93-112]
Extended finite element method Numerical Simulation of Crack Growth in the Glass Layer of Gallium-Arsenide Solar Cell [Volume 33, Issue 2, 2021, Pages 93-104]
Extinction Limits The Numerical Study of Extinction Limits and Structure of H2/O2 Counterflow Diffusion Flame with Ar and He Dilution [Volume 24, Issue 2, 2012, Pages 57-66]

F

Failure Numerical Simulation of Gas Flow inside the Orbit Valve Class 900 and its Effects on Parts Damages [Volume 30, Issue 2, 2018, Pages 125-136]
Fast filling Determine the Optimal Algorithm of Priority Panel in CNG Refueling Station to Minimize Energy Cost [Volume 32, Issue 2, 2020-2021, Pages 201-216]
Fatigue crack Growth The Effect of Fatigue Crack Growth on Mechanical Residual Stress Redistribution [Volume 27, Issue 2, 2016, Pages 1-10]
Fault tolerant control Fixed-time Fault Tolerant Control Based on Neural Network and Adaptive Sliding Mode Controller of Autonomous Underwater Vehicle with Actuator Saturation [(Articles in Press)]
Feed Feed effect on strain and stress in dome forming (spinning) of a tube in an aluminum CNG vessel manufacturing [Volume 32, Issue 2, 2020-2021, Pages 43-60]
Feedback Linearization Control Variable-Pitch Control of a Quadrotor Using Feedback Linearization Controller and Direct Adaptive Feedback Linearization Controller [Volume 31, Issue 2, 2020, Pages 67-90]
Feed Speed Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
FEM Experimental and Numerical Study on Aluminum Damage Using a Nonlinear Model of Continuum Damage Mechanics [Volume 27, Issue 2, 2016, Pages 41-54]
FEM The Effect of Winkler-Pasternak Foundation Coefficients on the Natural Frequency of Cylindrical Lattice Structures Using Galerkin Method [Volume 34, Issue 3, 2022, Pages 19-34]
Femoral prosthesis Reducing the stress shield in the femur using hip prostheses made of functionally graded materials [(Articles in Press)]
Ferrofluid Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
FGM Microgripper Electrostatically Actuated FGM Microgripper under the Effect of Thermal Moment [Volume 23, Issue 2, 2012, Pages 65-80]
Fick's law Study the Factors affecting the Moisture Diffusion Coefficient in Drying Clay Ceramics and Explanations the Analytical Model Process [Volume 27, Issue 1, 2016, Pages 87-102]
Film resistance Investigating the Effect of Film in SSRSW of Hastelloy X Superalloy [Volume 30, Issue 1, 2018, Pages 129-140]
Finite difference .Variable Damping in Geometric Nonlinear Plate Bending Analysis using Dynamic Relaxation Method [Volume 28, Issue 2, 2017, Pages 115-142]
Finite Element Finite Element Modeling of Laser Ultrasonics Process in Thermoelastic Regime [Volume 32, Issue 1, 2020-2021, Pages 133-152]
Finite Element Investigation of Fracture Mechanism in Single Point Incremental Forming of AA5052 Aluminum Alloy Using the Bao-Wierzbicki Damage Model [Volume 35, Issue 4, 2023, Pages 63-76]
Finite Element Analysis Damage Identification of Cylindrical Shells Based on Mode Shapes Curvature [Volume 30, Issue 1, 2018, Pages 119-128]
Finite Element Code Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method [Volume 28, Issue 1, 2017, Pages 123-131]
Finite-element method Numerical Simulation of Cranial Bone Perforation Process Using Water Jet [Volume 33, Issue 1, 2021, Pages 53-70]
Finite Element Method Experimental and Numerical Analysis of Flange Wrinkling of Bimetal Sheets in Deep Drawing Process [Volume 25, Issue 2, 2013, Pages 65-82]
Finite Element Method Evaluation of Crack Growth Criteria in Functionally Graded Polymer using Finite Element Metho [Volume 28, Issue 2, 2017, Pages 35-50]
Finite Element Method Modeling and Simulation of Growth in Diastolic Heart Failure [Volume 35, Issue 3, 2023, Pages 101-114]
Finite Element Method Reducing the stress shield in the femur using hip prostheses made of functionally graded materials [(Articles in Press)]
Finite Element Modeling Numerical Modeling of Linear Viscoelasticity in a Finite Element Method Software Package to be Used in Multiphysics Modeling [Volume 25, Issue 2, 2013, Pages 121-131]
Finite Elements Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Finite element simulation Analysis of Forming Parameters in Sheet Hydro-Forming Process [Volume 24, Issue 1, 2012, Pages 33-52]
Finite element simulation Experimental Study and Simulation of Tube Hydroforming Process of Bi-layered Aluminum-Copper with Axial Feeding [Volume 28, Issue 2, 2017, Pages 65-84]
Finite element simulation Geometry Effects of Asymmetrical Channel Sections on Common Defects in the Roll Forming Process [Volume 30, Issue 2, 2018, Pages 1-16]
Finite Element simulation (FEM) Study of the Effect of Process Parameters and Optimization of Bending Angle in Laser Bending [Volume 36, Issue 1, 2024, Pages 1-24]
Finite Volume Improvement of Aerodynamic Performance of Oscillating Airfoils with Plunging Motion at Low Reynolds Numbers Using Heat Transfer [Volume 30, Issue 1, 2018, Pages 79-96]
Finite Volume Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Finite-volume method Numerical Simulation of Cranial Bone Perforation Process Using Water Jet [Volume 33, Issue 1, 2021, Pages 53-70]
Finite Volume Method Direct Numerical Simulation of Supersonic and Transonic Compressible Viscous Flow by Kinetic Energy Preserving Scheme [Volume 28, Issue 1, 2017, Pages 15-30]
Fire Behavior Numerical Verification of the Effect of Side Wind on Fire of the Staircase of a Tall Building With Pyrosim Software [(Articles in Press)]
First order reliability method Improvement of Stability Transformation Method for First Order Reliability Analysis [Volume 28, Issue 2, 2017, Pages 143-152]
Five-hole probe Experimental Investigation of the Sail Position of a Submarine on the Downstream Flow Field [Volume 27, Issue 1, 2016, Pages 71-86]
Five-hole probe Experimental and Numerical Flow Investigation through a Radial Flow Compressor Volute [Volume 28, Issue 1, 2017, Pages 1-14]
Flame Location Investigation of Flame Location Effect on Flame Temperature in Premixed Counterflow Combustion of Particle-Cloud [Volume 26, Issue 1, 2015, Pages 119-128]
Flame shape Numerical Investigation of Wind Effects on the Flame Shape of Sarkhoon and Qeshm’s Refinery Flares [Volume 28, Issue 2, 2017, Pages 51-64]
Flame Temperature Investigation of Flame Location Effect on Flame Temperature in Premixed Counterflow Combustion of Particle-Cloud [Volume 26, Issue 1, 2015, Pages 119-128]
Flapping Amplitude Experimental Study of the Flapping Parameters on the MAV Aerodynamic Performance in Hovering Flight [Volume 27, Issue 2, 2016, Pages 87-98]
Flapping Frequency Experimental Study of the Flapping Parameters on the MAV Aerodynamic Performance in Hovering Flight [Volume 27, Issue 2, 2016, Pages 87-98]
Flares Numerical Investigation of Wind Effects on the Flame Shape of Sarkhoon and Qeshm’s Refinery Flares [Volume 28, Issue 2, 2017, Pages 51-64]
Flexibility Experimental Study of the Flapping Parameters on the MAV Aerodynamic Performance in Hovering Flight [Volume 27, Issue 2, 2016, Pages 87-98]
Floquet Theory Dynamic Stability Analysis of Rectangular Mindlin Plate in Contact with Fluid under Passage of Oscillating Rigid Bodies [Volume 34, Issue 4, 2022, Pages 65-88]
Flow Control Optimization of Suction Jet Length on NACA 0012 Airfoil with Using of Reynolds Stress Model (RSM) [Volume 25, Issue 1, 2013, Pages 61-76]
Flow Control Comparison of Single and L-PSJ DBD Plasma Actuators for Flow Control around a Cylinder [Volume 30, Issue 2, 2018, Pages 137-149]
Flow Control Applying Suction and Blowing Flow Control Approaches to Reduce the Flow-induced Instabilities of Elastically-mounted Square Cylinder [Volume 34, Issue 2, 2022, Pages 29-44]
Flow Control Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Flow distribution Improving the gas flow distribution in a PEMFC stack by removing liquid water from the manifold [Volume 34, Issue 3, 2022, Pages 1-14]
Flower pattern Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Flower pattern Effect of Flower Pattern on Uniform Distribution of Force on Rollers in Reshaping of Cold Roll Forming [Volume 34, Issue 1, 2022, Pages 49-60]
Flow field Experimental and Numerical Flow Investigation through a Radial Flow Compressor Volute [Volume 28, Issue 1, 2017, Pages 1-14]
Flow-induced vibration Applying Suction and Blowing Flow Control Approaches to Reduce the Flow-induced Instabilities of Elastically-mounted Square Cylinder [Volume 34, Issue 2, 2022, Pages 29-44]
Flow metering Designing and Numerical Analysis of Capillary Tube Thermal Mass Flowmeter as a Residential Natural Gas Meter [Volume 29, Issue 1, 2017, Pages 49-62]
Flow Separation Optimal Design of Divergent Part of an Over-expanded Nozzle Profile using Artificial Intelligence [Volume 35, Issue 1, 2023, Pages 19-36]
Flow Separation Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Fluid Conveying Microtube Nonlinear Vibration Analysis of Fluid Conveying Microtube under Parametric Magnetic Excitation [Volume 31, Issue 1, 2020, Pages 69-86]
Fluid flow rate Thermo-Economic evaluation of a solar dryer with evacuated heat pipe collector and energy storage [Volume 32, Issue 1, 2020-2021, Pages 39-58]
Fluid hydroforming pressure Experimental investigation and Numerical simulation of bending parameters on the spring back of the tube in the rotational bending process [(Articles in Press)]
Fluid Pressure Effect of Fluid Pressure on Weld-Line Movement and Thickness Distribution in Hydro-Mechanical Deep Drawing of Tailor-Welded Blanks (TWBs) [Volume 23, Issue 1, 2012, Pages 53-66]
Fluid-solid interaction Numerical Simulation of Gas Flow inside the Orbit Valve Class 900 and its Effects on Parts Damages [Volume 30, Issue 2, 2018, Pages 125-136]
Fluid-solid interaction Numerical study of the effect of elastic wall vibration mode on internal flow parameters [Volume 34, Issue 3, 2022, Pages 97-112]
Fluid Solid Interaction Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction [Volume 32, Issue 2, 2020-2021, Pages 133-148]
Fluid-structure interaction (FSI) VIV control in the flow over a cylinder using axial magnetic field [Volume 35, Issue 1, 2023, Pages 87-106]
Flux wave approach .Numerical Modelling of Water Hammer Problems based on the Flux Wave Approach and Baldwin-Lomax Turbulence Model [Volume 29, Issue 1, 2017, Pages 97-110]
Force analysis Numerical Simulation of Gas Flow inside the Orbit Valve Class 900 and its Effects on Parts Damages [Volume 30, Issue 2, 2018, Pages 125-136]
Force balancing Complete Dynamic Shaking Force Balancing of a 3(RPSP)-S Spherical Parallel Robot Using Extra Linkage [Volume 29, Issue 2, 2017, Pages 145-156]
Force convection Experimental Study of Wall Roughness Effects on the Frost Formation over a Cylinder [Volume 30, Issue 1, 2018, Pages 51-60]
Forced convection Effect of Air Gap between two Glass Covers on the Performance of Plane Solar Air Heaters [Volume 33, Issue 2, 2021, Pages 55-82]
Forced convection Numerical study of the effect of elastic wall vibration mode on internal flow parameters [Volume 34, Issue 3, 2022, Pages 97-112]
Forced vibration Forced Vibration Analysis of Machine Tools’ Hexapod Table [Volume 24, Issue 2, 2012, Pages 33-44]
Forming depth Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell [(Articles in Press)]
Forming limit curve Prediction of Forming Limit Curve Using Ductile Fracture Criteria in Hydrofoming of Aluminum Tubes [Volume 25, Issue 1, 2013, Pages 17-28]
Forming Limit Diagram (FLD) Investigation of Forming Limit and Weld Line Movement in the Forming of Tailor Welded Blanks using Experiment and Numerical Methods [Volume 23, Issue 2, 2012, Pages 1-16]
Forward Facing Step Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
Forward Kinematics Analysis A New Hybrid Strategy for Forward Kinematic Analysis of Parallel Robots [Volume 27, Issue 1, 2016, Pages 163-172]
Fourier Method The Effect of Winkler-Pasternak Foundation Coefficients on the Natural Frequency of Cylindrical Lattice Structures Using Galerkin Method [Volume 34, Issue 3, 2022, Pages 19-34]
Fracture Determination of the Critical Area and Reusability of Compressed Natural Gas Storage Cylinder in Collision [Volume 25, Issue 1, 2013, Pages 29-46]
Free Convection Natural Convection in a Porous Medium with Heat Generation: Self-Similar Solution [Volume 24, Issue 2, 2012, Pages 45-56]
Free Energy Modeling of a Stable Droplet Suspended in Vapor by Lattice Boltzmann Method [Volume 27, Issue 1, 2016, Pages 153-162]
Free fall test Experimental and Numerical Analysis of Single and Double layered Aluminum Sheet 3105 With Mechanical Joints under Drop Weight Impact [Volume 30, Issue 2, 2018, Pages 109-123]
Free Vibration Vibration of FGM Plates With Distributed Mass Using Third Order Shear Deformation Theory [Volume 26, Issue 2, 2015, Pages 55-71]
Free Vibration Free Vibration Analysis of Functionally Graded Rotating Double Tapered Beam by using Euler-bernoulli Beam Theory and Differential Transform Method [Volume 27, Issue 1, 2016, Pages 51-70]
Free Vibration Stability and Free Vibration Analysis of Plates with Random Material Property using Stochastic Finite Element Method [Volume 30, Issue 2, 2018, Pages 151-160]
Free Vibration Application of SSPH Method in Free Vibration Analysis of Graphene [Volume 31, Issue 2, 2020, Pages 53-66]
Frequency Numerical simulation of a micropump based on piezoelectric actuator [(Articles in Press)]
Frequency Constraint Multi-objective Optimization of Hybrid Laminated Composites under a Frequency Constraint by Using the Particle Swarm Optimization [Volume 24, Issue 2, 2012, Pages 97-113]
Friction factor Numerical investigation of heat transfer and pressure drop in a plate heat exchanger with Chevron plates [Volume 25, Issue 1, 2013, Pages 47-60]
Friction factor The Friction Factor of Turbulent Flow of the Base Fluid and Nanofluid in the Statistical Approach [Volume 31, Issue 1, 2020, Pages 105-122]
Friction Stir Welding Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas [(Articles in Press)]
Frost Experimental Study of Wall Roughness Effects on the Frost Formation over a Cylinder [Volume 30, Issue 1, 2018, Pages 51-60]
Fuel Assembly Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction [Volume 32, Issue 2, 2020-2021, Pages 133-148]
Fuel Droplet Thermal Radiation Heat Transfer Effects on Single Fuel Droplet Heat up Considering it’s Internal Circulation [Volume 23, Issue 1, 2012, Pages 67-82]
Fuel ratio Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Fuel Rod Numerical Model Development of Dummy Fuel Rod Under New Spacer Grids and End Constraints Using Experimental Modal Analysis [Volume 34, Issue 4, 2022, Pages 89-104]
Full Admission Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Functionally graded material (FGM) Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Functionally Graded Materials Simultaneous Estimation of Location and Strength of a Heat Source in a Functionally Graded Plate by Inverse Analysis [Volume 29, Issue 2, 2017, Pages 71-88]
Functionally Graded Materials Reducing the stress shield in the femur using hip prostheses made of functionally graded materials [(Articles in Press)]
Functionally Graded Polymer Evaluation of Crack Growth Criteria in Functionally Graded Polymer using Finite Element Metho [Volume 28, Issue 2, 2017, Pages 35-50]
Functionally graded smart plate Nonlinear Forced Vibration of Functionally Graded Magneto-Electro-Elastic Rectangular Plate based on the Third Order Shear Deformation Theory [Volume 30, Issue 2, 2018, Pages 47-66]
Fuzzy controller Beyond Pull-in Stabilization of a 2-DOF Torsional Micro-Actuator using a Fuzzy Controller [Volume 27, Issue 2, 2016, Pages 99-112]

G

Gait Optimization Dynamic Modeling and Optimal Walking Gait Planning of a Real Biped Robot Based on SLIP and Compass gait Models [Volume 30, Issue 1, 2018, Pages 31-50]
Galerkin method The Effect of Winkler-Pasternak Foundation Coefficients on the Natural Frequency of Cylindrical Lattice Structures Using Galerkin Method [Volume 34, Issue 3, 2022, Pages 19-34]
Gallium-Arsenide Solar Cell Numerical Simulation of Crack Growth in the Glass Layer of Gallium-Arsenide Solar Cell [Volume 33, Issue 2, 2021, Pages 93-104]
Galloping Applying Suction and Blowing Flow Control Approaches to Reduce the Flow-induced Instabilities of Elastically-mounted Square Cylinder [Volume 34, Issue 2, 2022, Pages 29-44]
Gas-Dynamic Similarity Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Gas-Solid Umerical Simulation of Elbow Erosion with Circumferential Welding in Two-Phase Gas Flow [Volume 31, Issue 2, 2020, Pages 141-156]
Gas-Solid Numerical simulation of inlet velocity and geometry effects of on the hydrodynamics of gas-solid turbulent flow in a fluidized bed reactor [(Articles in Press)]
Gastric cancer tissue Investigation of New Friction Models in Two-Dimensional Manipulation of Gastric Cancer Tissue [Volume 35, Issue 2, 2023, Pages 1-16]
Gauss’s laws Nonlinear Forced Vibration of Functionally Graded Magneto-Electro-Elastic Rectangular Plate based on the Third Order Shear Deformation Theory [Volume 30, Issue 2, 2018, Pages 47-66]
GDQ Method Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]
Generalized finite difference (GFD) method Two-dimensional Transient Dynamic Analysis of Decagonal Quasicrystals subjected to Shock Loading using Meshless Generalized Finite Difference (GFD) Method [Volume 30, Issue 1, 2018, Pages 97-118]
Generator Power Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Generator Power Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Genetic algorithm Geometric Optimization of Half Toroidal Continuously Variable Transmission Using Intelligent Techniques [Volume 23, Issue 1, 2012, Pages 29-40]
Genetic algorithm Optimal Design of Divergent Part of an Over-expanded Nozzle Profile using Artificial Intelligence [Volume 35, Issue 1, 2023, Pages 19-36]
Genetic algorithm Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Genetic algorithm Analysis of fracture behavior of carbon nitride poly crystalline by genetic algorithm and molecular dynamics methods [(Articles in Press)]
Geometrical defects Experimental Study of the Roll Forming of PVC / Glass Fabric Composite Laminates [Volume 28, Issue 2, 2017, Pages 21-34]
Geometric and dynamic parameters An Investigation on the Effects of Geometric and Dynamic Parameters on the Truck Lateral Deviation Due to the Braking Force Imbalance [Volume 26, Issue 2, 2015, Pages 141-152]
Geometry Numerical study of the effect of geometry and metal foam on the energy absorption of nested profiles [Volume 34, Issue 3, 2022, Pages 67-78]
Geothermal Thermoeconomic Optimization of a Superheated Kalina Cycle for Various Geothermal Source Temperatures in Iran [Volume 33, Issue 1, 2021, Pages 1-16]
Geothermal Evaluation of an integrated solar-geothermal energy system to provide power, heat and cooling [Volume 34, Issue 4, 2022, Pages 19-34]
Gibbs-Appell Implementation of Gibbs-Appell method in dynamic analysis of a novel serial-parallel hybrid robot PP-(3RSS-PS) [Volume 36, Issue 1, 2024, Pages 77-92]
Gibbs-Appell Modeling and simulation of contact and friction forces in flexible robotic arms [(Articles in Press)]
Gibbs Appell's method Application of Reinforcement Learning for Navigation of a Planar Snake Robot in Serpentine Locomotion [Volume 26, Issue 1, 2015, Pages 97-118]
Giesekus model Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Glass reinforced laminated composite Numerical And Experimental Investigation of deflection of Laminated composites due to drop weight of different projectiles [Volume 33, Issue 2, 2021, Pages 41-54]
Gold Nanoparticles Investigating the effect of HK friction model input parameters on the force and critical time in gold nanoparticle manipulation [Volume 35, Issue 4, 2023, Pages 1-16]
Grafting percent (%) The Grafting of a Nylon Fiber Surface by a Mixture of Two Acrylic Monomers and the Evaluation of Optimum Values by using a Traditional Design of Experiment Software [Volume 31, Issue 1, 2020, Pages 39-52]
Granular material Design a shape-shifting robot gripper with granular material [Volume 25, Issue 2, 2013, Pages 33-46]
Graphene Analyzing Mechanical Properties of Aluminum-graphene Nanocomposite with Vacancy and Pin-holed Defects by Molecular Dynamics Method [(Articles in Press)]
Graphic Processor Parallel Thomas Approach in Computational Fluid Dynamics with GPUs- Lid-driven Cavity [Volume 28, Issue 2, 2017, Pages 152-164]
Gravitational instability On the Dynamical Stability of Astrophysical Rings [Volume 29, Issue 2, 2017, Pages 89-98]
Gyroscopic moment Effects of Gyroscopic Moment on the Dynamics and Vibrations of a High- Speed Double- Helical Gear Pair [Volume 29, Issue 1, 2017, Pages 31-48]

H

Half- car model Robust-Adaptive Sliding Mode Controller Design with Fault tolerance for Active Suspension of Half-car model [Volume 34, Issue 3, 2022, Pages 79-96]
Half-car model؛ suspension system؛ Non-linear vibration؛ Chaos An investigation on the Resonances and Chaotic Behavior of a Nonlinear Vehicle Suspension System [Volume 24, Issue 1, 2012, Pages 53-70]
Hamilton’s principle Introducing a New Crack Disturbance Function for Transverse Vibration Analysis of a Cracked Beam [Volume 25, Issue 2, 2013, Pages 19-32]
Harmonic actuation Investigation of the Effect of Geometrical and Mechanical Properties of Horizontal Wind Turbines on its Dynamic Behavior for Free and Forced Vibration Case [Volume 27, Issue 2, 2016, Pages 113-128]
Harmony Search Meta-Heuristic Algorithm Introduction of Harmony Search Algorithm for Aerodynamic Shape Optimization Using the Navier-Stokes Equations [Volume 24, Issue 2, 2012, Pages 81-96]
Hastelloy X Investigating the Effect of Film in SSRSW of Hastelloy X Superalloy [Volume 30, Issue 1, 2018, Pages 129-140]
Heart Diseases Modeling and Simulation of Growth in Diastolic Heart Failure [Volume 35, Issue 3, 2023, Pages 101-114]
Heat and mass transfer Experimental Study of Wall Roughness Effects on the Frost Formation over a Cylinder [Volume 30, Issue 1, 2018, Pages 51-60]
Heat exchanger Simulation of fluid flow in a heat exchanger with elastic intermediate separator at different working conditions [Volume 32, Issue 2, 2020-2021, Pages 77-92]
Heat Recovery Steam Generator (HRSG) Multi Objective Optimization of Converting an Old Steam Power Plant to Combined Cycle Power Plant (CCPP) Using Double and Single Pressure Heat Recovery Steam Generator (HRSG) via Genetic Algorithm [Volume 27, Issue 2, 2016, Pages 129-139]
Heat Source Simultaneous Estimation of Location and Strength of a Heat Source in a Functionally Graded Plate by Inverse Analysis [Volume 29, Issue 2, 2017, Pages 71-88]
Heat transfer Numerical investigation of heat transfer and pressure drop in a plate heat exchanger with Chevron plates [Volume 25, Issue 1, 2013, Pages 47-60]
Heat transfer Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Heat transfer Numerical and Analytical Investigation of Thermal Dispersion Effects on the Heat Transfer of Nanofluid flow inside a Channel [Volume 29, Issue 2, 2017, Pages 21-40]
Heat transfer Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Heat transfer Simultaneous Estimation of Location and Strength of a Heat Source in a Functionally Graded Plate by Inverse Analysis [Volume 29, Issue 2, 2017, Pages 71-88]
Heat transfer Improvement of Aerodynamic Performance of Oscillating Airfoils with Plunging Motion at Low Reynolds Numbers Using Heat Transfer [Volume 30, Issue 1, 2018, Pages 79-96]
Heat transfer Numerical Simulation of the Heat-Fluid Flow Behavior Around the Cylinder with the Controller Wire [Volume 31, Issue 2, 2020, Pages 105-126]
Heat transfer Numerical Study of Flow and Heat Transfer in Cavity Receiver Tube of a Solar Power Tower with Different Inserts under Non-uniform Heat flux [Volume 35, Issue 2, 2023, Pages 17-36]
Heat transfer Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
Heat transfer enhancement Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Heat transfer rate Investigating the Effect of Angle and Length of Vortex Generators with Sinusoidal Structure on Compact Heat Exchangers Performance [(Articles in Press)]
Heat treatment Optimization of Hardening Heat treatment of Oil Extraction Machine’s Cylinder Made of Stainless steel [(Articles in Press)]
HED Grinding Superficial Hardening of AISI1045 Steel in High Efficiency Deep Grinding Through Optimization Approaches, Taguchi Method and SA Algorithm [Volume 24, Issue 1, 2012, Pages 87-102]
Height control Multimode wheeled mobile robot with height control on uneven surfaces [Volume 27, Issue 1, 2016, Pages 173-184]
Height of blades Parametric study and numerical analysis of the regenerative compressor with symmetric aerodynamic blades, to improve performance [Volume 32, Issue 2, 2020-2021, Pages 1-18]
Helical coiled tube Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Helical Gear A Novel Method to Improve Crack Detection Ability in Helical Gear [Volume 31, Issue 1, 2020, Pages 1-12]
Helicopter Body and Rotor Simulation of Flow Field around a Generic Helicopter Fuselage by Modeling the Rotor [Volume 25, Issue 1, 2013, Pages 1-16]
Helium shielding gas Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas [(Articles in Press)]
Heller Thermal Performance Analysis of Natural Draft Dry Cooling Towers Based on New Theoretical Method [Volume 32, Issue 1, 2020-2021, Pages 191-210]
Hexapod Forced Vibration Analysis of Machine Tools’ Hexapod Table [Volume 24, Issue 2, 2012, Pages 33-44]
High cycle fatigue Prediction of High Cycle Fatigue Life with Variable Loading Amplitude using Thermography Method [(Articles in Press)]
High Efficiency Deep Grinding Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
High Lift Devices Numerical Study of Improving the Aerodynamic Performance of the High Lift Devices in the Two-Element Airfoil [Volume 35, Issue 1, 2023, Pages 37-52]
High- speed Effects of Gyroscopic Moment on the Dynamics and Vibrations of a High- Speed Double- Helical Gear Pair [Volume 29, Issue 1, 2017, Pages 31-48]
HK friction model Investigating the effect of HK friction model input parameters on the force and critical time in gold nanoparticle manipulation [Volume 35, Issue 4, 2023, Pages 1-16]
Homotopy perturbation Stability Analysis of Nano-wire Made Tweezers in Magnetic Flux [Volume 32, Issue 2, 2020-2021, Pages 149-164]
Horizontal axis wind turbine Investigation of the Effect of Geometrical and Mechanical Properties of Horizontal Wind Turbines on its Dynamic Behavior for Free and Forced Vibration Case [Volume 27, Issue 2, 2016, Pages 113-128]
Horseshoe vortex Experimental Investigation of the Sail Position of a Submarine on the Downstream Flow Field [Volume 27, Issue 1, 2016, Pages 71-86]
Hot-wire anemometer Experimental Investigation on Flow Downstream of a Square Bluff Body at Different Angles [Volume 31, Issue 2, 2020, Pages 177-187]
HT29 cancerous cell Experimental Determination of HT29 Cancerous Cell Surface Roughness by Atomic Force Microscopy to be Applied in Nanomanipulation [Volume 28, Issue 1, 2017, Pages 111-122]
Hybrid robot Implementation of Gibbs-Appell method in dynamic analysis of a novel serial-parallel hybrid robot PP-(3RSS-PS) [Volume 36, Issue 1, 2024, Pages 77-92]
Hydraulic–Electric Analogy A New Mathematical Model Gas Flows in Pipeline with Leak [Volume 31, Issue 1, 2020, Pages 155-164]
Hydrodynamic Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Hydrodynamic deep drawing Analysis of Forming Parameters in Sheet Hydro-Forming Process [Volume 24, Issue 1, 2012, Pages 33-52]
Hydrodynamic deep drawing Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method [Volume 28, Issue 1, 2017, Pages 123-131]
Hydrodynamic Lubrication Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]
Hydroforming pressure Experimental and Numerical Investigation of Pressure-Induced Changes in Tube Thickness Distribution and Cross-Section during Rotary Bending [(Articles in Press)]
Hydro-Mechanical Deep Drawing Effect of Fluid Pressure on Weld-Line Movement and Thickness Distribution in Hydro-Mechanical Deep Drawing of Tailor-Welded Blanks (TWBs) [Volume 23, Issue 1, 2012, Pages 53-66]
Hygrothermal environment The effect of material degradation on the bending of laminated plates [Volume 34, Issue 2, 2022, Pages 1-14]
Hyperelasticity Solution of Nonlinear Compressible Hyperelastic Problems by Isogeometric Analysis Method [Volume 30, Issue 2, 2018, Pages 67-82]

I

Immersed boundary method Simulation of Particle Motion in Non-Newtonian Fluids by Immersed Boundary Lattice Boltzmann Method [Volume 28, Issue 1, 2017, Pages 75-92]
Impact Experimental and Numerical Investigation on Concrete Specimens with Expanded Metal Sheet under Impact Loading [Volume 32, Issue 1, 2020-2021, Pages 211-230]
Imperialist Competitive Algorithm Optimal Design of Vessels by using Imperialist Competitive Algorithm [Volume 25, Issue 1, 2013, Pages 125-134]
Impingement Heat Transfer Numerical Simulation of the Effect of the Location of Impinging Jets on the Convective Heat Transfer from a Cylindrical Concave Surface [Volume 27, Issue 2, 2016, Pages 71-86]
Impinging Pulsated Jet Numerical Simulation of the Effects of Sinusoidal Pulsed Impinging Jet on Heat Transfer from the Concave Cylindrical Surface [Volume 29, Issue 1, 2017, Pages 17-30]
In738 machining Vibration Cutting and Elliptical Ultrasonic Vibration Assisted Turning of In738 Work-Pieces [Volume 23, Issue 2, 2012, Pages 17-28]
Inclination angle Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Inclination angle of chamber Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
Incompressible flow Numerical study of the effect of elastic wall vibration mode on internal flow parameters [Volume 34, Issue 3, 2022, Pages 97-112]
Incremental sheet forming Investigation of Fracture Mechanism in Single Point Incremental Forming of AA5052 Aluminum Alloy Using the Bao-Wierzbicki Damage Model [Volume 35, Issue 4, 2023, Pages 63-76]
Induced vibrations Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction [Volume 32, Issue 2, 2020-2021, Pages 133-148]
Injection Molding Simulation of Rubber Vulcanization for Calculation of the Curing Time with Modification of the Kinetic Model [Volume 26, Issue 2, 2015, Pages 107-118]
Integration Semi-implicit Integration of Constitutive Equations with Non-linear Mixed Hardening [Volume 32, Issue 1, 2020-2021, Pages 111-132]
Interaction Integral Method Evaluation of Crack Growth Criteria in Functionally Graded Polymer using Finite Element Metho [Volume 28, Issue 2, 2017, Pages 35-50]
Inverse Design Introduction of Harmony Search Algorithm for Aerodynamic Shape Optimization Using the Navier-Stokes Equations [Volume 24, Issue 2, 2012, Pages 81-96]
Inverse Heat Transfer Problem Estimation of Heat Shocks in Inverse Heat Transfer Problems using Kalman Filtering [Volume 26, Issue 2, 2015, Pages 45-54]
Inverse kinematics Complete Dynamic Shaking Force Balancing of a 3(RPSP)-S Spherical Parallel Robot Using Extra Linkage [Volume 29, Issue 2, 2017, Pages 145-156]
Inverse Problems Simultaneous Estimation of Location and Strength of a Heat Source in a Functionally Graded Plate by Inverse Analysis [Volume 29, Issue 2, 2017, Pages 71-88]
Inviscid Compressible Flow Application of Adaptive Time Spectral Method to Analyze Inviscid Compressible Flow Around a Pitching Airfoil [Volume 35, Issue 1, 2023, Pages 1-18]
Isogeometric Analysis Effect of Superconvergent Stress Points for Solution Improvement and Error Estimation of Isogeometric Analysis of Axisymmetric Problems [Volume 26, Issue 1, 2015, Pages 79-95]
Isogeometric Analysis Improvement of Stress and Error Estimation by Patch Equilibrium in Isogeometric Analysisic analysis [Volume 26, Issue 2, 2015, Pages 73-87]
Isogeometric Analysis Solution of Nonlinear Compressible Hyperelastic Problems by Isogeometric Analysis Method [Volume 30, Issue 2, 2018, Pages 67-82]

J

J Integral The Effect of Fatigue Crack Growth on Mechanical Residual Stress Redistribution [Volume 27, Issue 2, 2016, Pages 1-10]
J-Integral Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas [(Articles in Press)]
Johnson SB Probability Distribution Function The Friction Factor of Turbulent Flow of the Base Fluid and Nanofluid in the Statistical Approach [Volume 31, Issue 1, 2020, Pages 105-122]
Joint clearance The Effects of Revolute Joint Clearance on the Kinematic Behavior of the 3RPR Planar Parallel Manipulator [Volume 31, Issue 1, 2020, Pages 39-52]
Journal Bearing Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]

K

Kalman Filtering Estimation of Heat Shocks in Inverse Heat Transfer Problems using Kalman Filtering [Volume 26, Issue 2, 2015, Pages 45-54]
Key words: energy consumption Investigating the effect of optimizing external skins and translucent walls on reducing energy consumption and investment return time of educational buildings in a temperate climate with dry and very hot summers [Volume 36, Issue 1, 2024, Pages 41-60]
Kinematics The Effects of Revolute Joint Clearance on the Kinematic Behavior of the 3RPR Planar Parallel Manipulator [Volume 31, Issue 1, 2020, Pages 39-52]
Kinematics and Dynamics Kinematics and Dynamics of a Snake Robot with Worm Like Locomotion on Inclined Surface [Volume 24, Issue 1, 2012, Pages 71-86]
Kinetic Energy Preserving Scheme Direct Numerical Simulation of Supersonic and Transonic Compressible Viscous Flow by Kinetic Energy Preserving Scheme [Volume 28, Issue 1, 2017, Pages 15-30]

L

Laminar flow Nanoparticle Shape Effect on a Nanofluid-Based Parabolic Trough Concentrating Photovoltaic/Thermal System [Volume 29, Issue 2, 2017, Pages 41-56]
Laminar flow Numerical Simulation of the Heat-Fluid Flow Behavior Around the Cylinder with the Controller Wire [Volume 31, Issue 2, 2020, Pages 105-126]
Laminar flow Numerical Analysis of Transition in Laminar Flow around a Pithing Airfoil [(Articles in Press)]
Laminar & Turbulent Flow Study of Unsteady Viscous Turbulent Flow with High Reynolds Passing One, Two & Three Cylinders by Random Vortex Method (RVM) [Volume 24, Issue 1, 2012, Pages 133-146]
Laminated composite plates The effect of material degradation on the bending of laminated plates [Volume 34, Issue 2, 2022, Pages 1-14]
Large Deflection Modeling of large deflection of the chromium nanobeams using design of experiments method [Volume 35, Issue 4, 2023, Pages 107-120]
Large Deformation Theoretical and Experimental Thermal Post Buckling Analysis of Columns [Volume 26, Issue 2, 2015, Pages 129-140]
Large deformations .Variable Damping in Geometric Nonlinear Plate Bending Analysis using Dynamic Relaxation Method [Volume 28, Issue 2, 2017, Pages 115-142]
Large-eddy simulation Large-Eddy Simulation of Turbulent Square Duct Flow [Volume 31, Issue 1, 2020, Pages 13-22]
Laser Finite Element Modeling of Laser Ultrasonics Process in Thermoelastic Regime [Volume 32, Issue 1, 2020-2021, Pages 133-152]
Laser bending Study of the Effect of Process Parameters and Optimization of Bending Angle in Laser Bending [Volume 36, Issue 1, 2024, Pages 1-24]
Laser forming proces Experimental Investigation on Process Parameters Effects in Laser Forming of Closed-cell Aluminium Foam Sheets [Volume 26, Issue 2, 2015, Pages 33-44]
Lateral Deviation Theoretical and Experimental Investigation on the Vehicle Lateral Deviation Due to the Braking Force Error [Volume 23, Issue 1, 2012, Pages 41-52]
Lateral Deviation An Investigation on the Effects of Geometric and Dynamic Parameters on the Truck Lateral Deviation Due to the Braking Force Imbalance [Volume 26, Issue 2, 2015, Pages 141-152]
Lateral force Design a shape-shifting robot gripper with granular material [Volume 25, Issue 2, 2013, Pages 33-46]
Lattice Boltzmann Modeling of a Stable Droplet Suspended in Vapor by Lattice Boltzmann Method [Volume 27, Issue 1, 2016, Pages 153-162]
Lattice Boltzmann method Different Methods to Compute Force over a Cylinder by LBM [Volume 25, Issue 1, 2013, Pages 114-123]
Lattice Boltzmann method Simulation of Particle Motion in Non-Newtonian Fluids by Immersed Boundary Lattice Boltzmann Method [Volume 28, Issue 1, 2017, Pages 75-92]
Lattice Boltzmann method Numerical Investigation of Particle Deposition in a Room using Large Eddy Simulation based on Lattice Boltzmann Method [Volume 30, Issue 2, 2018, Pages 83-94]
Lattice Composite Structure The Effect of Winkler-Pasternak Foundation Coefficients on the Natural Frequency of Cylindrical Lattice Structures Using Galerkin Method [Volume 34, Issue 3, 2022, Pages 19-34]
LBM method Heat Transfer of Nanofluid in a Channel with Magnetic Field and Porous Obstacle using the Darcy-Brinkman-Forchheimer Model in the LBM Method [Volume 32, Issue 1, 2020-2021, Pages 153-172]
Leakage A New Mathematical Model Gas Flows in Pipeline with Leak [Volume 31, Issue 1, 2020, Pages 155-164]
Length of mixing chamber Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Lift Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Lift and Drag Coefficient Optimization of Suction Jet Length on NACA 0012 Airfoil with Using of Reynolds Stress Model (RSM) [Volume 25, Issue 1, 2013, Pages 61-76]
Lift & Drag Coefficients Study of Wing Shapes Influence on MAV Aerodynamic Coefficients [Volume 23, Issue 2, 2012, Pages 29-46]
Linear hardening Theoretical Solution of Linear Hardening Elastic-plastic Deformation Length for a Roll Formed Channel [Volume 24, Issue 1, 2012, Pages 19-32]
Linearized force model Comparison of Single and L-PSJ DBD Plasma Actuators for Flow Control around a Cylinder [Volume 30, Issue 2, 2018, Pages 137-149]
Linear Viscoelasticity Numerical Modeling of Linear Viscoelasticity in a Finite Element Method Software Package to be Used in Multiphysics Modeling [Volume 25, Issue 2, 2013, Pages 121-131]
Liquid Jet Injection Experiments on the Formation Process of Bag Breakup Regime of Injected Liquid Jet into an Airstream [Volume 31, Issue 2, 2020, Pages 1-18]
Lithium Ion Battery Electrochemical-Thermal Simulation of Cell Lithium-Ion Battery of Electrical Vehicle [Volume 31, Issue 2, 2020, Pages 33-52]
Lithium-ion battery cooling Cooling of lithium-ion battery assemblies using nanofluids by heat sink [Volume 33, Issue 1, 2021, Pages 111-93]
Lithium Ion Concentration Electrochemical-Thermal Simulation of Cell Lithium-Ion Battery of Electrical Vehicle [Volume 31, Issue 2, 2020, Pages 33-52]
Liver cancer tissue Using new friction models to investigate the mechanical properties of liver cancer tissue [(Articles in Press)]
Liver tissue Investigating the effect of different positions of the slot on performance of single-slot and double-slot coaxial antenna in the treatment of cancer in liver tissue by hyperthermia method [Volume 35, Issue 3, 2023, Pages 17-32]
Locomotion Multimode wheeled mobile robot with height control on uneven surfaces [Volume 27, Issue 1, 2016, Pages 173-184]
London goodness factor Investigating the Effect of Angle and Length of Vortex Generators with Sinusoidal Structure on Compact Heat Exchangers Performance [(Articles in Press)]
Longitudinal bow Geometry Effects of Asymmetrical Channel Sections on Common Defects in the Roll Forming Process [Volume 30, Issue 2, 2018, Pages 1-16]
Longitudinal strain Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Loss Modelling Experimental and Numerical Study of Partial Admission Effect on Flow Distribution in Supersonic Turbine Axial-Gap [Volume 24, Issue 2, 2012, Pages 17-32]
Low Reynolds number Simulation of nanofluid flow at low Reynolds number in a microchannel with one-sided sudden expansion under the effect of a magnetic field [Volume 35, Issue 3, 2023, Pages 85-100]
Low Reynolds Number flow Study of Wing Shapes Influence on MAV Aerodynamic Coefficients [Volume 23, Issue 2, 2012, Pages 29-46]
Low velocity impact Numerical And Experimental Investigation of deflection of Laminated composites due to drop weight of different projectiles [Volume 33, Issue 2, 2021, Pages 41-54]
L-PSJ actuators Comparison of Single and L-PSJ DBD Plasma Actuators for Flow Control around a Cylinder [Volume 30, Issue 2, 2018, Pages 137-149]
Lubrication Investigation of Slip Condition in the Elastohydrodynamic Lubrication [(Articles in Press)]

M

Machining forces Forced Vibration Analysis of Machine Tools’ Hexapod Table [Volume 24, Issue 2, 2012, Pages 33-44]
Machining parameters Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel [Volume 23, Issue 2, 2012, Pages 99-110]
Magnetic field Heat Transfer of Nanofluid in a Channel with Magnetic Field and Porous Obstacle using the Darcy-Brinkman-Forchheimer Model in the LBM Method [Volume 32, Issue 1, 2020-2021, Pages 153-172]
Magnetic field VIV control in the flow over a cylinder using axial magnetic field [Volume 35, Issue 1, 2023, Pages 87-106]
Magnetic field Simulation of nanofluid flow at low Reynolds number in a microchannel with one-sided sudden expansion under the effect of a magnetic field [Volume 35, Issue 3, 2023, Pages 85-100]
Magnetic field Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
Manifold Improving the gas flow distribution in a PEMFC stack by removing liquid water from the manifold [Volume 34, Issue 3, 2022, Pages 1-14]
Material degradation The effect of material degradation on the bending of laminated plates [Volume 34, Issue 2, 2022, Pages 1-14]
Material gradation angle Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Mathematical model Thermal Performance Analysis of Natural Draft Dry Cooling Towers Based on New Theoretical Method [Volume 32, Issue 1, 2020-2021, Pages 191-210]
Mathematical modeling A New Mathematical Model Gas Flows in Pipeline with Leak [Volume 31, Issue 1, 2020, Pages 155-164]
MAV Study of Wing Shapes Influence on MAV Aerodynamic Coefficients [Volume 23, Issue 2, 2012, Pages 29-46]
Maximum rectangle method Optimization of Combined Cooling Heating and Power System (CCHP) by a Novel Hybrid Method [Volume 30, Issue 1, 2018, Pages 61-78]
MCF-10 cancer tissue Experimental and Theoretical Investigation of Young's Modulus of Breast Cancer Tissue (MCF-10) Using Different Cantilevers of Atomic Force Microscope [Volume 36, Issue 1, 2024, Pages 61-76]
Mechanical properties Investigation of Chemical Composition Influence on Mechanical Properties of API X65 Microalloyed Steel [Volume 23, Issue 2, 2012, Pages 47-64]
Mechanical properties Investigation of the Effect of Geometric Defects and Temperature Changes on the Fracture Behavior of Boron Carbide Monocrystalline Structure by Molecular Dynamics [Volume 34, Issue 1, 2022, Pages 37-48]
Mechanical properties Investigating the mechanical properties of polymer composite materials made by 3D printing method [Volume 35, Issue 4, 2023, Pages 77-89]
Mechanical properties Analysis of fracture behavior of carbon nitride poly crystalline by genetic algorithm and molecular dynamics methods [(Articles in Press)]
Mechanical properties Analyzing Mechanical Properties of Aluminum-graphene Nanocomposite with Vacancy and Pin-holed Defects by Molecular Dynamics Method [(Articles in Press)]
Mechanical properties Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas [(Articles in Press)]
Mechanical Systems A High Accuracy Method for Solving the Differential-Algebraic Equations Arising in Mechanical Systems [Volume 36, Issue 1, 2024, Pages 107-122]
Membrane Humidifier Investigating the Effect of Polymer Membrane Characteristics on the Performance of the Membrane Humidifier [Volume 35, Issue 4, 2023, Pages 17-32]
Meshless local Petrov-Galerkin (MLPG) method Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Meshless method Two-dimensional Transient Dynamic Analysis of Decagonal Quasicrystals subjected to Shock Loading using Meshless Generalized Finite Difference (GFD) Method [Volume 30, Issue 1, 2018, Pages 97-118]
Meshless method Application of SSPH Method in Free Vibration Analysis of Graphene [Volume 31, Issue 2, 2020, Pages 53-66]
Metaheuristics Parameter Optimization of Various Solar Cell Models by Neural Network Algorithm [Volume 36, Issue 1, 2024, Pages 123-142]
Metal/Composite Hybrid (FML) Free vibration analysis of sandwich panel plate with FML face sheet and flexible core using third-order shear deformation theory [Volume 34, Issue 4, 2022, Pages 1-18]
Methyl Acrylate The Grafting of a Nylon Fiber Surface by a Mixture of Two Acrylic Monomers and the Evaluation of Optimum Values by using a Traditional Design of Experiment Software [Volume 31, Issue 1, 2020, Pages 39-52]
Micro actuator Beyond Pull-in Stabilization of a 2-DOF Torsional Micro-Actuator using a Fuzzy Controller [Volume 27, Issue 2, 2016, Pages 99-112]
Microfluidic Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
Microfluidic Numerical simulation of a micropump based on piezoelectric actuator [(Articles in Press)]
Microfluidics Numerical simulation of viscoelastic fluid mixing in a T-Y shaped micromixer [(Articles in Press)]
Micro-hardness Study on the effects of ball burnishing parameters and initial surface roughness on the core roughness characteristics of Copper cylindrical parts [Volume 32, Issue 2, 2020-2021, Pages 113-132]
Microhardness Superficial Hardening of AISI1045 Steel in High Efficiency Deep Grinding Through Optimization Approaches, Taguchi Method and SA Algorithm [Volume 24, Issue 1, 2012, Pages 87-102]
Microhardness Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
Micro-Mixer Numerical Analysis of Magnetic Mixing Phenomenon in an Electroosmotic Flow between Two Parallel Plates [Volume 32, Issue 1, 2020-2021, Pages 174-190]
Microstructure Superficial Hardening of AISI1045 Steel in High Efficiency Deep Grinding Through Optimization Approaches, Taguchi Method and SA Algorithm [Volume 24, Issue 1, 2012, Pages 87-102]
Microstructure Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
Micro tube Simulation of the Forced Convection Heat Transfer Non-Newtonian Nanofluid, Aqueous Solution of Carboxymethyl Cellulose-Aluminum Oxide, in Slip Flow Regime Through a Microtube [Volume 28, Issue 1, 2017, Pages 47-62]
Microwave Investigating the effect of different positions of the slot on performance of single-slot and double-slot coaxial antenna in the treatment of cancer in liver tissue by hyperthermia method [Volume 35, Issue 3, 2023, Pages 17-32]
Mindlin Plate Dynamic Stability Analysis of Rectangular Mindlin Plate in Contact with Fluid under Passage of Oscillating Rigid Bodies [Volume 34, Issue 4, 2022, Pages 65-88]
Mixed convection Numerical analysis of mix convection of sodium alginate non-Newtonian fluid with 〖Al〗_2 O_3nanoparticle in a channel with block [Volume 32, Issue 1, 2020-2021, Pages 93-110]
Mixed-Mode dynamic fracture analysis Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Mixing Analysis Of Mixing Efficiency In An Electroosmotically Micromixer With Heterogeneous Wall Charge Distribution [Volume 25, Issue 2, 2013, Pages 97-110]
Mixing Bed Material and Biomass Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Mixing Efficiency Numerical Analysis of Magnetic Mixing Phenomenon in an Electroosmotic Flow between Two Parallel Plates [Volume 32, Issue 1, 2020-2021, Pages 174-190]
Mixing index Numerical simulation of viscoelastic fluid mixing in a T-Y shaped micromixer [(Articles in Press)]
Mixing Vanes Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction [Volume 32, Issue 2, 2020-2021, Pages 133-148]
Mobile Robot Multimode wheeled mobile robot with height control on uneven surfaces [Volume 27, Issue 1, 2016, Pages 173-184]
Modal Test Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Modeling Dynamic Modeling and Optimal Walking Gait Planning of a Real Biped Robot Based on SLIP and Compass gait Models [Volume 30, Issue 1, 2018, Pages 31-50]
Modeling Variable-Pitch Control of a Quadrotor Using Feedback Linearization Controller and Direct Adaptive Feedback Linearization Controller [Volume 31, Issue 2, 2020, Pages 67-90]
Modeling Numerical and Experimental Investigation on the Parabolic Dish SolarConcentrator [Volume 32, Issue 1, 2020-2021, Pages 17-38]
Modeling Determine the Optimal Algorithm of Priority Panel in CNG Refueling Station to Minimize Energy Cost [Volume 32, Issue 2, 2020-2021, Pages 201-216]
Modeling Investigation of Slip Condition in the Elastohydrodynamic Lubrication [(Articles in Press)]
Mode shape Modeling and simulation of contact and friction forces in flexible robotic arms [(Articles in Press)]
Mode Shapes Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Modified gravity On the Dynamical Stability of Astrophysical Rings [Volume 29, Issue 2, 2017, Pages 89-98]
Molecular Dynamics The Effect of Interatomic Potential Function on Nanometric Machining of Single Crystal Silicon [Volume 30, Issue 2, 2018, Pages 17-32]
Molecular Dynamics Investigation of the Effect of Geometric Defects and Temperature Changes on the Fracture Behavior of Boron Carbide Monocrystalline Structure by Molecular Dynamics [Volume 34, Issue 1, 2022, Pages 37-48]
Molecular Dynamics Analysis of fracture behavior of carbon nitride poly crystalline by genetic algorithm and molecular dynamics methods [(Articles in Press)]
Molecular Dynamics Analyzing Mechanical Properties of Aluminum-graphene Nanocomposite with Vacancy and Pin-holed Defects by Molecular Dynamics Method [(Articles in Press)]
Momentum exchange Different Methods to Compute Force over a Cylinder by LBM [Volume 25, Issue 1, 2013, Pages 114-123]
Monolithic Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Monopropellant thruster Investigation of the Effect of Catalyst Granule Diameter on the Performance of Decomposition Chamber of a Hydrazine Catalytic Thruster [Volume 35, Issue 4, 2023, Pages 33-46]
Monte-Carlo Simulation Statistical Analysis of Piezoelectric Energy Harvesting in the Bridge Systems [Volume 28, Issue 1, 2017, Pages 31-46]
Monte-Carlo Simulation Stability and Free Vibration Analysis of Plates with Random Material Property using Stochastic Finite Element Method [Volume 30, Issue 2, 2018, Pages 151-160]
Morphing Wing Aerodynamic Performance Investigation of an Experimental Variable-Span Morphing Wing Model [Volume 27, Issue 1, 2016, Pages 35-50]
Motion simulator Implementation of Gibbs-Appell method in dynamic analysis of a novel serial-parallel hybrid robot PP-(3RSS-PS) [Volume 36, Issue 1, 2024, Pages 77-92]
Moveable nozzle Effects of Divergence Angle on Moveable Nozzle Performance in Thrust Vector Control System [Volume 26, Issue 1, 2015, Pages 1-15]
Moving Surface Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Multimode Multimode wheeled mobile robot with height control on uneven surfaces [Volume 27, Issue 1, 2016, Pages 173-184]
Multi-Objective Optimization Multi-objective Optimization of Hybrid Laminated Composites under a Frequency Constraint by Using the Particle Swarm Optimization [Volume 24, Issue 2, 2012, Pages 97-113]
Multiphase flow Experiments on the Formation Process of Bag Breakup Regime of Injected Liquid Jet into an Airstream [Volume 31, Issue 2, 2020, Pages 1-18]
Multiphysics Numerical Modeling of Linear Viscoelasticity in a Finite Element Method Software Package to be Used in Multiphysics Modeling [Volume 25, Issue 2, 2013, Pages 121-131]

N

NACA 0012 Investigating the Effect of Moving Surface on NACA 0012 Airfoil in High Speed Ratio [Volume 35, Issue 3, 2023, Pages 75-84]
Nanobeam Modeling of large deflection of the chromium nanobeams using design of experiments method [Volume 35, Issue 4, 2023, Pages 107-120]
Nanocomposite Analyzing Mechanical Properties of Aluminum-graphene Nanocomposite with Vacancy and Pin-holed Defects by Molecular Dynamics Method [(Articles in Press)]
Nano fluid Numerical analysis of mix convection of sodium alginate non-Newtonian fluid with 〖Al〗_2 O_3nanoparticle in a channel with block [Volume 32, Issue 1, 2020-2021, Pages 93-110]
Nanofluid Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Nanofluid Study of entropy generation and evaluation statistical heat transfer properties in turbulent flow [Volume 29, Issue 1, 2017, Pages 63-80]
Nanofluid Nanoparticle Shape Effect on a Nanofluid-Based Parabolic Trough Concentrating Photovoltaic/Thermal System [Volume 29, Issue 2, 2017, Pages 41-56]
Nanofluid Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Nanofluid Heat Transfer of Nanofluid in a Channel with Magnetic Field and Porous Obstacle using the Darcy-Brinkman-Forchheimer Model in the LBM Method [Volume 32, Issue 1, 2020-2021, Pages 153-172]
Nanofluid Cooling of lithium-ion battery assemblies using nanofluids by heat sink [Volume 33, Issue 1, 2021, Pages 111-93]
Nanofluid Effect of microtube addition on thermal and hydrodynamic behavior of microchannel heatsink for nanofluid Flow [Volume 34, Issue 1, 2022, Pages 21-36]
Nanofluid Numerical study of forced convection in a microchannel in the presence of nanofluid using the slip condition [Volume 34, Issue 4, 2022, Pages 53-64]
Nanofluid Numerical analysis of the obstacle effect with different geometry on the heat transfer of nanofluid flow in a rectangular channel [Volume 35, Issue 3, 2023, Pages 51-64]
Nanofluid Simulation of nanofluid flow at low Reynolds number in a microchannel with one-sided sudden expansion under the effect of a magnetic field [Volume 35, Issue 3, 2023, Pages 85-100]
Nanofluid, Jet impingement Comparison between Single-Phase, Two-Phase Mixture and Eulerian-Eulerian Models for the Simulation of Jet Impingement of Nanofluids [Volume 27, Issue 2, 2016, Pages 55-70]
Nanofluids Numerical and Analytical Investigation of Thermal Dispersion Effects on the Heat Transfer of Nanofluid flow inside a Channel [Volume 29, Issue 2, 2017, Pages 21-40]
Nanomanipulation Experimental Determination of HT29 Cancerous Cell Surface Roughness by Atomic Force Microscopy to be Applied in Nanomanipulation [Volume 28, Issue 1, 2017, Pages 111-122]
Nanomanipulation Investigation of New Friction Models in Two-Dimensional Manipulation of Gastric Cancer Tissue [Volume 35, Issue 2, 2023, Pages 1-16]
Nanomanipulation Manipulation of breast cell tissue with the aim of calculating Young's modulus, using Tatara contact theory and atomic force microscopy [Volume 35, Issue 3, 2023, Pages 1-16]
Nanomanipulation Investigating the effect of HK friction model input parameters on the force and critical time in gold nanoparticle manipulation [Volume 35, Issue 4, 2023, Pages 1-16]
Nanometric Machining The Effect of Interatomic Potential Function on Nanometric Machining of Single Crystal Silicon [Volume 30, Issue 2, 2018, Pages 17-32]
Nanoparticles shape Nanoparticle Shape Effect on a Nanofluid-Based Parabolic Trough Concentrating Photovoltaic/Thermal System [Volume 29, Issue 2, 2017, Pages 41-56]
Nano-tweezers Stability Analysis of Nano-wire Made Tweezers in Magnetic Flux [Volume 32, Issue 2, 2020-2021, Pages 149-164]
Natural convection Effect of Air Gap between two Glass Covers on the Performance of Plane Solar Air Heaters [Volume 33, Issue 2, 2021, Pages 55-82]
Natural draft dry cooling tower Thermal Performance Analysis of Natural Draft Dry Cooling Towers Based on New Theoretical Method [Volume 32, Issue 1, 2020-2021, Pages 191-210]
Natural Frequency Effect of Piezoelectric Patches on the Vibration and Buckling of Euler-Bernoulli Beams under Axial Load [Volume 27, Issue 2, 2016, Pages 29-40]
Natural Frequency The Effect of Winkler-Pasternak Foundation Coefficients on the Natural Frequency of Cylindrical Lattice Structures Using Galerkin Method [Volume 34, Issue 3, 2022, Pages 19-34]
Natural Frequency Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Natural Frequency and Mode Shape Numerical Model Development of Dummy Fuel Rod Under New Spacer Grids and End Constraints Using Experimental Modal Analysis [Volume 34, Issue 4, 2022, Pages 89-104]
Natural gas Determine the Optimal Algorithm of Priority Panel in CNG Refueling Station to Minimize Energy Cost [Volume 32, Issue 2, 2020-2021, Pages 201-216]
Natural gas leakage Presenting a Correlation to Obtain Natural Gas Leakage Rate from a Buried High-Pressure Pipeline in a Porous Media [Volume 32, Issue 1, 2020-2021, Pages 231-254]
Navier-Stokes Numerical Analysis of Magnetic Mixing Phenomenon in an Electroosmotic Flow between Two Parallel Plates [Volume 32, Issue 1, 2020-2021, Pages 174-190]
Navier-Stokes Equations Introduction of Harmony Search Algorithm for Aerodynamic Shape Optimization Using the Navier-Stokes Equations [Volume 24, Issue 2, 2012, Pages 81-96]
Navier-Stokes Equations Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
Navier-Stokes Equations Numerical study of the effect of elastic wall vibration mode on internal flow parameters [Volume 34, Issue 3, 2022, Pages 97-112]
Nested profiles Numerical study of the effect of geometry and metal foam on the energy absorption of nested profiles [Volume 34, Issue 3, 2022, Pages 67-78]
Neural Network Investigation of Chemical Composition Influence on Mechanical Properties of API X65 Microalloyed Steel [Volume 23, Issue 2, 2012, Pages 47-64]
Neural Network Flow prediction in two-dimensional asymmetric diffuser by neural network and comparison with three turbulence models and experimental data [Volume 34, Issue 2, 2022, Pages 45-60]
Neural Network Fixed-time Fault Tolerant Control Based on Neural Network and Adaptive Sliding Mode Controller of Autonomous Underwater Vehicle with Actuator Saturation [(Articles in Press)]
Neural network algorithm Parameter Optimization of Various Solar Cell Models by Neural Network Algorithm [Volume 36, Issue 1, 2024, Pages 123-142]
Newmark method Mixed-Mode Dynamic Fracture Analysis of FGM Plate by MFree Method [Volume 25, Issue 2, 2013, Pages 1-18]
Noise Spur Gear Profile Modification for the Reduction of Static Transmission Error [Volume 29, Issue 2, 2017, Pages 129-144]
Nondestructive evaluation Finite Element Modeling of Laser Ultrasonics Process in Thermoelastic Regime [Volume 32, Issue 1, 2020-2021, Pages 133-152]
Nonholonomic System Dynamics Modeling and Analysis a New Mechanism for Automatic Control of Angular Velocity of a Rotary Axis [Volume 26, Issue 2, 2015, Pages 1-13]
Non-linear Control Nonlinear Control of Motion of A Spherical Robot on Inclined Surfaces Based on Feedback Linearization Method [Volume 31, Issue 2, 2020, Pages 91-104]
Nonlinear vibrations Nonlinear Vibration Analysis of Fluid Conveying Microtube under Parametric Magnetic Excitation [Volume 31, Issue 1, 2020, Pages 69-86]
Nonlocal Elastisity Theory Nonlinear Vibration Analysis of Fluid Conveying Microtube under Parametric Magnetic Excitation [Volume 31, Issue 1, 2020, Pages 69-86]
Non-Newtonian nanofluid Simulation of the Forced Convection Heat Transfer Non-Newtonian Nanofluid, Aqueous Solution of Carboxymethyl Cellulose-Aluminum Oxide, in Slip Flow Regime Through a Microtube [Volume 28, Issue 1, 2017, Pages 47-62]
Non-uniform blank-holder force Automatic determination of non-uniform blank-holder force in sheet metal forming [Volume 34, Issue 1, 2022, Pages 81-96]
Nozzle Profile Optimal Design of Divergent Part of an Over-expanded Nozzle Profile using Artificial Intelligence [Volume 35, Issue 1, 2023, Pages 19-36]
Number of blades Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Numerical The Numerical Study of Extinction Limits and Structure of H2/O2 Counterflow Diffusion Flame with Ar and He Dilution [Volume 24, Issue 2, 2012, Pages 57-66]
Numerical Numerical and Experimental Investigation of Aerodynamic of Quadrotor Blades in low Reynolds [Volume 27, Issue 1, 2016, Pages 135-152]
Numerical and Experimental Modal Analysis Numerical Model Development of Dummy Fuel Rod Under New Spacer Grids and End Constraints Using Experimental Modal Analysis [Volume 34, Issue 4, 2022, Pages 89-104]
Numerical Control Look-Ahead NURBS-PH Interpolators for High Speed CNC Milling [Volume 23, Issue 1, 2012, Pages 83-96]
Numerical Method Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Numerical Method Numerical Modeling of Linear Viscoelasticity in a Finite Element Method Software Package to be Used in Multiphysics Modeling [Volume 25, Issue 2, 2013, Pages 121-131]
Numerical methods A High Accuracy Method for Solving the Differential-Algebraic Equations Arising in Mechanical Systems [Volume 36, Issue 1, 2024, Pages 107-122]
Numerical modeling Numerical Investigation of Silica Gel-Water Adsorption Chillers with Plate Fins Bed [Volume 25, Issue 1, 2013, Pages 95-113]
Numerical modeling Investigating the Effect of Polymer Membrane Characteristics on the Performance of the Membrane Humidifier [Volume 35, Issue 4, 2023, Pages 17-32]
Numerical simulation Numerical investigation of heat transfer and pressure drop in a plate heat exchanger with Chevron plates [Volume 25, Issue 1, 2013, Pages 47-60]
Numerical simulation Simulation of Rubber Vulcanization for Calculation of the Curing Time with Modification of the Kinetic Model [Volume 26, Issue 2, 2015, Pages 107-118]
Numerical simulation Comparison between Single-Phase, Two-Phase Mixture and Eulerian-Eulerian Models for the Simulation of Jet Impingement of Nanofluids [Volume 27, Issue 2, 2016, Pages 55-70]
Numerical simulation Numerical Investigation of Wind Effects on the Flame Shape of Sarkhoon and Qeshm’s Refinery Flares [Volume 28, Issue 2, 2017, Pages 51-64]
Numerical simulation Numerical Analysis of Magnetic Mixing Phenomenon in an Electroosmotic Flow between Two Parallel Plates [Volume 32, Issue 1, 2020-2021, Pages 174-190]
Numerical simulation Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
Numerical simulation Numerical Simulation of Cranial Bone Perforation Process Using Water Jet [Volume 33, Issue 1, 2021, Pages 53-70]
Numerical simulation VIV control in the flow over a cylinder using axial magnetic field [Volume 35, Issue 1, 2023, Pages 87-106]
Numerical simulation Introduction of a Modified Phenomenological Model for Single and Annular Plasma Synthetic Jet Actuators [Volume 35, Issue 4, 2023, Pages 91-106]
Numerical simulation‎ Numerical Investigation of Drag Reduction Mechanism in Laminar Flow Regime using Rectangular Riblets [Volume 31, Issue 1, 2020, Pages 165-173]
Numerical Simulations Simulation of Flow Field around a Generic Helicopter Fuselage by Modeling the Rotor [Volume 25, Issue 1, 2013, Pages 1-16]
Numerical Solution Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]
Numerical Solution Numerical simulation of turbulent heat transfer in boiler with supercritical fluid and asymmetric thermal conditions [(Articles in Press)]
Numerical study Numerical And Experimental Investigation of deflection of Laminated composites due to drop weight of different projectiles [Volume 33, Issue 2, 2021, Pages 41-54]
Numerical study Numerical analysis of the obstacle effect with different geometry on the heat transfer of nanofluid flow in a rectangular channel [Volume 35, Issue 3, 2023, Pages 51-64]
NURBS Solution of Nonlinear Compressible Hyperelastic Problems by Isogeometric Analysis Method [Volume 30, Issue 2, 2018, Pages 67-82]
Nusselt Number Natural Convection in a Porous Medium with Heat Generation: Self-Similar Solution [Volume 24, Issue 2, 2012, Pages 45-56]
Nusselt Number Numerical Simulation of the Effect of the Location of Impinging Jets on the Convective Heat Transfer from a Cylindrical Concave Surface [Volume 27, Issue 2, 2016, Pages 71-86]
Nusselt Number Numerical Simulation of the Effects of Sinusoidal Pulsed Impinging Jet on Heat Transfer from the Concave Cylindrical Surface [Volume 29, Issue 1, 2017, Pages 17-30]
Nusselt Number Study of entropy generation and evaluation statistical heat transfer properties in turbulent flow [Volume 29, Issue 1, 2017, Pages 63-80]
Nusselt Number Simulation of fluid flow in a heat exchanger with elastic intermediate separator at different working conditions [Volume 32, Issue 2, 2020-2021, Pages 77-92]
Nusselt Number Numerical study of the effect of non-uniform magnetic field on ferrofluid heat transfer in a channel containing a double-forwrad facing step [(Articles in Press)]
Nylon Fibers The Grafting of a Nylon Fiber Surface by a Mixture of Two Acrylic Monomers and the Evaluation of Optimum Values by using a Traditional Design of Experiment Software [Volume 31, Issue 1, 2020, Pages 39-52]

O

Oblique shock Effects of Divergence Angle on Moveable Nozzle Performance in Thrust Vector Control System [Volume 26, Issue 1, 2015, Pages 1-15]
Oil extraction machine Optimization of Hardening Heat treatment of Oil Extraction Machine’s Cylinder Made of Stainless steel [(Articles in Press)]
One dimensional vibration tool One And Two Dimensional Ultrasonic Vibration Tool [Volume 26, Issue 1, 2015, Pages 35-50]
One-way Highway Numerical Investigation of Darrieus Wind Turbine near a One-way Highway [Volume 32, Issue 1, 2020-2021, Pages 1-16]
Online Estimation Method Estimation of Heat Shocks in Inverse Heat Transfer Problems using Kalman Filtering [Volume 26, Issue 2, 2015, Pages 45-54]
OpenFOAM Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Optical properties Improving Optical Quality of Poly methyl methacrylate Sheet by Forming with Rubber [Volume 29, Issue 1, 2017, Pages 1-16]
Optimization Optimization of one Stage Axial Compressor by using Quasi-Three Dimensional Design and Hybrid Genetic Algorithm [Volume 26, Issue 1, 2015, Pages 63-78]
Optimization Determine the Optimal Algorithm of Priority Panel in CNG Refueling Station to Minimize Energy Cost [Volume 32, Issue 2, 2020-2021, Pages 201-216]
Optimization Thermoeconomic Optimization of a Superheated Kalina Cycle for Various Geothermal Source Temperatures in Iran [Volume 33, Issue 1, 2021, Pages 1-16]
Optimization Optimal Design of Divergent Part of an Over-expanded Nozzle Profile using Artificial Intelligence [Volume 35, Issue 1, 2023, Pages 19-36]
Optimization Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Optimization Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Optimization Parameter Optimization of Various Solar Cell Models by Neural Network Algorithm [Volume 36, Issue 1, 2024, Pages 123-142]
Optimization Study of the Effect of Process Parameters and Optimization of Bending Angle in Laser Bending [Volume 36, Issue 1, 2024, Pages 1-24]
Optimization" Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Optimization procedure Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel [Volume 23, Issue 2, 2012, Pages 99-110]
Orbit valves Numerical Simulation of Gas Flow inside the Orbit Valve Class 900 and its Effects on Parts Damages [Volume 30, Issue 2, 2018, Pages 125-136]
Oscillating airfoil Investigation of Suction Jet Parameters in Flow Control of Dynamic Stall [Volume 32, Issue 2, 2020-2021, Pages 181-200]
Oscillating Rigid Body Dynamic Stability Analysis of Rectangular Mindlin Plate in Contact with Fluid under Passage of Oscillating Rigid Bodies [Volume 34, Issue 4, 2022, Pages 65-88]
Oscillatory and rotational movements Experimental study of measurement of free oscillations of a cylinder with fin in wind tunnel under different Reynolds [Volume 35, Issue 4, 2023, Pages 47-62]

P

Parabolic Dish Solar Concentrator Numerical and Experimental Investigation on the Parabolic Dish SolarConcentrator [Volume 32, Issue 1, 2020-2021, Pages 17-38]
Parabolic trough solar collector Evaluation of energy and exergy of a parabolic trough solar collector equipped with internal fin and star turbulator absorber tube [(Articles in Press)]
Parachute Simulation Derivation of Aerodynamic Characteristics of a Ribbon Parachute by Truck Tow Test [Volume 36, Issue 1, 2024, Pages 25-40]
Parallel Processing Parallel Thomas Approach in Computational Fluid Dynamics with GPUs- Lid-driven Cavity [Volume 28, Issue 2, 2017, Pages 152-164]
Parallel Robot A New Hybrid Strategy for Forward Kinematic Analysis of Parallel Robots [Volume 27, Issue 1, 2016, Pages 163-172]
Parallel Thomas approach Parallel Thomas Approach in Computational Fluid Dynamics with GPUs- Lid-driven Cavity [Volume 28, Issue 2, 2017, Pages 152-164]
Parameter identification Parameter Optimization of Various Solar Cell Models by Neural Network Algorithm [Volume 36, Issue 1, 2024, Pages 123-142]
Parameters identification Boundary Condition Identification of a Clamped Beam in the Flexible Support [Volume 28, Issue 2, 2017, Pages 85-96]
Parametric Magnetic Resonance Nonlinear Vibration Analysis of Fluid Conveying Microtube under Parametric Magnetic Excitation [Volume 31, Issue 1, 2020, Pages 69-86]
Parametric Uncertainty Nonlinear Control of Motion of A Spherical Robot on Inclined Surfaces Based on Feedback Linearization Method [Volume 31, Issue 2, 2020, Pages 91-104]
Parces Method Introduction of Harmony Search Algorithm for Aerodynamic Shape Optimization Using the Navier-Stokes Equations [Volume 24, Issue 2, 2012, Pages 81-96]
Partial Admission Experimental and Numerical Study of Partial Admission Effect on Flow Distribution in Supersonic Turbine Axial-Gap [Volume 24, Issue 2, 2012, Pages 17-32]
Partial Admission Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Particle-Cloud Investigation of Flame Location Effect on Flame Temperature in Premixed Counterflow Combustion of Particle-Cloud [Volume 26, Issue 1, 2015, Pages 119-128]
Particle Deposition Numerical Investigation of Particle Deposition in a Room using Large Eddy Simulation based on Lattice Boltzmann Method [Volume 30, Issue 2, 2018, Pages 83-94]
Particle fraction Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Particle swarm optimization Multi-objective Optimization of Hybrid Laminated Composites under a Frequency Constraint by Using the Particle Swarm Optimization [Volume 24, Issue 2, 2012, Pages 97-113]
Partitioned Comparison of Monolithic and Partitioned Approaches for the Solution of Fluid-Solid Thermal Interaction Problems [Volume 31, Issue 1, 2020, Pages 23-38]
Passive micromixer Analysis Of Mixing Efficiency In An Electroosmotically Micromixer With Heterogeneous Wall Charge Distribution [Volume 25, Issue 2, 2013, Pages 97-110]
Patchy charge distribution Analysis Of Mixing Efficiency In An Electroosmotically Micromixer With Heterogeneous Wall Charge Distribution [Volume 25, Issue 2, 2013, Pages 97-110]
PCM Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
PEM fuel cell Improving the gas flow distribution in a PEMFC stack by removing liquid water from the manifold [Volume 34, Issue 3, 2022, Pages 1-14]
Performance Investigation on Improvement of Radial Porous Burners in Comparison to Conventional Porous Burners [Volume 23, Issue 1, 2012, Pages 15-28]
Performance evaluation criteria Evaluation of energy and exergy of a parabolic trough solar collector equipped with internal fin and star turbulator absorber tube [(Articles in Press)]
Permanent displacement Experimental and Numerical Analysis of Single and Double layered Aluminum Sheet 3105 With Mechanical Joints under Drop Weight Impact [Volume 30, Issue 2, 2018, Pages 109-123]
Phase change materials Thermo-Economic evaluation of a solar dryer with evacuated heat pipe collector and energy storage [Volume 32, Issue 1, 2020-2021, Pages 39-58]
Phase change materials Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
Phason displacement Two-dimensional Transient Dynamic Analysis of Decagonal Quasicrystals subjected to Shock Loading using Meshless Generalized Finite Difference (GFD) Method [Volume 30, Issue 1, 2018, Pages 97-118]
PH Curve Look-Ahead NURBS-PH Interpolators for High Speed CNC Milling [Volume 23, Issue 1, 2012, Pages 83-96]
Phenomenology A Phenomenological Study of Polygonal Hydraulic Jumps [Volume 31, Issue 1, 2020, Pages 87-104]
Phonon displacement Two-dimensional Transient Dynamic Analysis of Decagonal Quasicrystals subjected to Shock Loading using Meshless Generalized Finite Difference (GFD) Method [Volume 30, Issue 1, 2018, Pages 97-118]
Photovoltaic panel Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Photovoltaic/Thermal system Nanoparticle Shape Effect on a Nanofluid-Based Parabolic Trough Concentrating Photovoltaic/Thermal System [Volume 29, Issue 2, 2017, Pages 41-56]
Piezoelectric Statistical Analysis of Piezoelectric Energy Harvesting in the Bridge Systems [Volume 28, Issue 1, 2017, Pages 31-46]
Piezoelectric Beam The Electric Response of Piezoelectric Beam Using Dynamic Stiffness Method [Volume 31, Issue 2, 2020, Pages 127-140]
Piezoelectric Patch Effect of Piezoelectric Patches on the Vibration and Buckling of Euler-Bernoulli Beams under Axial Load [Volume 27, Issue 2, 2016, Pages 29-40]
Pipeline A New Mathematical Model Gas Flows in Pipeline with Leak [Volume 31, Issue 1, 2020, Pages 155-164]
Pipeline Presenting a Correlation to Obtain Natural Gas Leakage Rate from a Buried High-Pressure Pipeline in a Porous Media [Volume 32, Issue 1, 2020-2021, Pages 231-254]
Pitching airfoil Periodic Unsteady Transonic Compressible Flow Simulation using Fourier-Based Algorithm [Volume 25, Issue 2, 2013, Pages 47-64]
Pitching airfoil Application of Adaptive Time Spectral Method to Analyze Inviscid Compressible Flow Around a Pitching Airfoil [Volume 35, Issue 1, 2023, Pages 1-18]
Pitch to chord ratio Parametric study and numerical analysis of the regenerative compressor with symmetric aerodynamic blades, to improve performance [Volume 32, Issue 2, 2020-2021, Pages 1-18]
Plane Air Heater Effect of Air Gap between two Glass Covers on the Performance of Plane Solar Air Heaters [Volume 33, Issue 2, 2021, Pages 55-82]
Planetary Gear Set Dynamics Modeling and Analysis a New Mechanism for Automatic Control of Angular Velocity of a Rotary Axis [Volume 26, Issue 2, 2015, Pages 1-13]
Planform Study of Wing Shapes Influence on MAV Aerodynamic Coefficients [Volume 23, Issue 2, 2012, Pages 29-46]
Plasma actuators Comparison of Single and L-PSJ DBD Plasma Actuators for Flow Control around a Cylinder [Volume 30, Issue 2, 2018, Pages 137-149]
Plateau–Rayleigh Instability A Phenomenological Study of Polygonal Hydraulic Jumps [Volume 31, Issue 1, 2020, Pages 87-104]
Plate Bending Stability and Free Vibration Analysis of Plates with Random Material Property using Stochastic Finite Element Method [Volume 30, Issue 2, 2018, Pages 151-160]
Plate deflection Numerical And Experimental Investigation of deflection of Laminated composites due to drop weight of different projectiles [Volume 33, Issue 2, 2021, Pages 41-54]
Plate heat exchanger Numerical investigation of heat transfer and pressure drop in a plate heat exchanger with Chevron plates [Volume 25, Issue 1, 2013, Pages 47-60]
Pollutants, Efficiency Numerical Simulation of Toos Power Plant Boiler to Improve its Thermal Efficiency [Volume 27, Issue 1, 2016, Pages 117-134]
Pollutants emission Investigation on Improvement of Radial Porous Burners in Comparison to Conventional Porous Burners [Volume 23, Issue 1, 2012, Pages 15-28]
Polycrystalline Analysis of fracture behavior of carbon nitride poly crystalline by genetic algorithm and molecular dynamics methods [(Articles in Press)]
Polygonal Jump A Phenomenological Study of Polygonal Hydraulic Jumps [Volume 31, Issue 1, 2020, Pages 87-104]
Poly Methyl Meth Acrylate Improving Optical Quality of Poly methyl methacrylate Sheet by Forming with Rubber [Volume 29, Issue 1, 2017, Pages 1-16]
Pontryagin’s Minimum Principle An Improved Shooting Method for a Class of Switching Optimal Control Problems [Volume 31, Issue 1, 2020, Pages 123-138]
Porosity Coefficient Investigating the Effect of Polymer Membrane Characteristics on the Performance of the Membrane Humidifier [Volume 35, Issue 4, 2023, Pages 17-32]
Porous Frequency Analysis of Cracked Porous Functionally Graded Beams on Elastic Foundation using Reddy Third Order Shear Deformation Theory [Volume 32, Issue 2, 2020-2021, Pages 93-112]
Porous Burner Investigation on Improvement of Radial Porous Burners in Comparison to Conventional Porous Burners [Volume 23, Issue 1, 2012, Pages 15-28]
Porous cavity Conjugate Heat Transfer in Closed Cavity with Porous Blocks [Volume 29, Issue 1, 2017, Pages 111-121]
Post- Thermal Buckling Theoretical and Experimental Thermal Post Buckling Analysis of Columns [Volume 26, Issue 2, 2015, Pages 129-140]
Potential Function The Effect of Interatomic Potential Function on Nanometric Machining of Single Crystal Silicon [Volume 30, Issue 2, 2018, Pages 17-32]
Potential Velocity Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
Power-law liquids Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
Power-law non-Newtonian fluids Simulation of Particle Motion in Non-Newtonian Fluids by Immersed Boundary Lattice Boltzmann Method [Volume 28, Issue 1, 2017, Pages 75-92]
Power Plant Numerical Simulation of Toos Power Plant Boiler to Improve its Thermal Efficiency [Volume 27, Issue 1, 2016, Pages 117-134]
Power production Evaluation of an integrated solar-geothermal energy system to provide power, heat and cooling [Volume 34, Issue 4, 2022, Pages 19-34]
Power Transmission؛ Continuously Variable Transmission؛ Half Toroidal؛ Optimization Geometric Optimization of Half Toroidal Continuously Variable Transmission Using Intelligent Techniques [Volume 23, Issue 1, 2012, Pages 29-40]
Prediction and Modeling Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Prefabricated building Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
Pressure drop Curvature Ratio and Pitch Spacing Effect of Helical Coiled Tube on Pressure Drop and Heat Transfer Behavior of TiO2/Water Nanofluid laminar Flow [Volume 25, Issue 1, 2013, Pages 77-94]
Pressure path Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method [Volume 28, Issue 1, 2017, Pages 123-131]
Prime movers Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Probability density function Study of entropy generation and evaluation statistical heat transfer properties in turbulent flow [Volume 29, Issue 1, 2017, Pages 63-80]
Profiles Modification Spur Gear Profile Modification for the Reduction of Static Transmission Error [Volume 29, Issue 2, 2017, Pages 129-144]
Protuberance Experimental Investigation of the Influence of Transverse Dual protuberances on the Thrust Vector of a Supersonic C-D nozzle [Volume 31, Issue 1, 2020, Pages 139-154]
Pseudocritical point Numerical simulation of turbulent heat transfer in boiler with supercritical fluid and asymmetric thermal conditions [(Articles in Press)]
Pseudospectral method A High Accuracy Method for Solving the Differential-Algebraic Equations Arising in Mechanical Systems [Volume 36, Issue 1, 2024, Pages 107-122]
Pull-in instability Beyond Pull-in Stabilization of a 2-DOF Torsional Micro-Actuator using a Fuzzy Controller [Volume 27, Issue 2, 2016, Pages 99-112]
Pull-in Voltage Electrostatically Actuated FGM Microgripper under the Effect of Thermal Moment [Volume 23, Issue 2, 2012, Pages 65-80]
Pulse on-time The Study of the Effect of Input Parameters on Material Romoval Rate, %Tool Water Ratio and Surface Roughness of AISI H13 Tool Steel in the Electrical Discharge Machining (EDM) [Volume 24, Issue 1, 2012, Pages 123-132]
PVC Thermoplastic Experimental Study of the Roll Forming of PVC / Glass Fabric Composite Laminates [Volume 28, Issue 2, 2017, Pages 21-34]
Pyrosim Software Numerical Verification of the Effect of Side Wind on Fire of the Staircase of a Tall Building With Pyrosim Software [(Articles in Press)]

Q

Q-learning Application of Reinforcement Learning for Navigation of a Planar Snake Robot in Serpentine Locomotion [Volume 26, Issue 1, 2015, Pages 97-118]
Quasicrystals Two-dimensional Transient Dynamic Analysis of Decagonal Quasicrystals subjected to Shock Loading using Meshless Generalized Finite Difference (GFD) Method [Volume 30, Issue 1, 2018, Pages 97-118]

R

Radial Flow Investigation on Improvement of Radial Porous Burners in Comparison to Conventional Porous Burners [Volume 23, Issue 1, 2012, Pages 15-28]
Radial flow compressor Experimental and Numerical Flow Investigation through a Radial Flow Compressor Volute [Volume 28, Issue 1, 2017, Pages 1-14]
Radial turbine Scaling of a Radial Turbine for Turbocharger of a Lean Combustion Engine [Volume 32, Issue 2, 2020-2021, Pages 165-180]
Radiant tube Numerical Study of the Effects of Structural and Functional Parameters on Unmixed Combustion of Natural Gas in Three Radiant Tubes with Different Geometries [Volume 33, Issue 2, 2021, Pages 83-92]
Radiometer pumps An Experimental Study of Crookes Radiometer [Volume 33, Issue 1, 2021, Pages 17-34]
Radiometric force An Experimental Study of Crookes Radiometer [Volume 33, Issue 1, 2021, Pages 17-34]
Random Vortex Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
Random Vortex Method Study of Unsteady Viscous Turbulent Flow with High Reynolds Passing One, Two & Three Cylinders by Random Vortex Method (RVM) [Volume 24, Issue 1, 2012, Pages 133-146]
Range and Endurance Aerodynamic Performance Investigation of an Experimental Variable-Span Morphing Wing Model [Volume 27, Issue 1, 2016, Pages 35-50]
Rarified flow An Experimental Study of Crookes Radiometer [Volume 33, Issue 1, 2021, Pages 17-34]
Rectangular cantilevers Experimental and Theoretical Investigation of Young's Modulus of Breast Cancer Tissue (MCF-10) Using Different Cantilevers of Atomic Force Microscope [Volume 36, Issue 1, 2024, Pages 61-76]
Rectangular channel Numerical analysis of the obstacle effect with different geometry on the heat transfer of nanofluid flow in a rectangular channel [Volume 35, Issue 3, 2023, Pages 51-64]
Redistribution of Residual Stress The Effect of Fatigue Crack Growth on Mechanical Residual Stress Redistribution [Volume 27, Issue 2, 2016, Pages 1-10]
Regenerative flow compressor Parametric study and numerical analysis of the regenerative compressor with symmetric aerodynamic blades, to improve performance [Volume 32, Issue 2, 2020-2021, Pages 1-18]
Regression model Modeling of large deflection of the chromium nanobeams using design of experiments method [Volume 35, Issue 4, 2023, Pages 107-120]
Regular Polygon A Phenomenological Study of Polygonal Hydraulic Jumps [Volume 31, Issue 1, 2020, Pages 87-104]
Reinforcement learning Application of Reinforcement Learning for Navigation of a Planar Snake Robot in Serpentine Locomotion [Volume 26, Issue 1, 2015, Pages 97-118]
Reinforcement learning Combining the principles of fuzzy logic and reinforcement learning for control of dynamic systems [Volume 27, Issue 1, 2016, Pages 103-116]
Relative curvature Numerical and Experimental Investigations on Strip Deformation in Cage Roll Forming Process for Pipes with Small Thickness/Diameter Ratio [Volume 23, Issue 1, 2012, Pages 1-14]
Relative equivalent uniform annual benefit Optimization of Combined Cooling Heating and Power System (CCHP) by a Novel Hybrid Method [Volume 30, Issue 1, 2018, Pages 61-78]
Reshaping of cold roll forming Effect of Flower Pattern on Uniform Distribution of Force on Rollers in Reshaping of Cold Roll Forming [Volume 34, Issue 1, 2022, Pages 49-60]
Residential Natural Gas Meter Designing and Numerical Analysis of Capillary Tube Thermal Mass Flowmeter as a Residential Natural Gas Meter [Volume 29, Issue 1, 2017, Pages 49-62]
Residual stress؛ multi-pass girth weld؛ thermomechanical steel pipe؛ natural gas transmission؛ hole drilling Experimental Determination of Residual Stresses in Multi-Pass Girth Welding of Thermo-Mechanical Steel Pipe [Volume 25, Issue 2, 2013, Pages 111-120]
Response surface method Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Response Surface Method (RSM) Study of the Effect of Process Parameters and Optimization of Bending Angle in Laser Bending [Volume 36, Issue 1, 2024, Pages 1-24]
Restitution Coefficient Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Reynolds equation Investigation of Slip Condition in the Elastohydrodynamic Lubrication [(Articles in Press)]
Reynolds Number Simulating of Laminar and Turbulent Flows Inside Diverging Channels with Random Vortex Method (RVM) and Investigating the Effects of the Angle of Divergence and the Reynolds Number on the Recirculating Flow Inside the Channels [Volume 26, Issue 1, 2015, Pages 17-34]
Reynolds Number Improvement of Aerodynamic Performance of Oscillating Airfoils with Plunging Motion at Low Reynolds Numbers Using Heat Transfer [Volume 30, Issue 1, 2018, Pages 79-96]
Reynolds Number Simulation of fluid flow in a heat exchanger with elastic intermediate separator at different working conditions [Volume 32, Issue 2, 2020-2021, Pages 77-92]
Reynolds Number Experimental study of measurement of free oscillations of a cylinder with fin in wind tunnel under different Reynolds [Volume 35, Issue 4, 2023, Pages 47-62]
Rheological Model Numerical Modeling of Linear Viscoelasticity in a Finite Element Method Software Package to be Used in Multiphysics Modeling [Volume 25, Issue 2, 2013, Pages 121-131]
Ribbon Parachute Derivation of Aerodynamic Characteristics of a Ribbon Parachute by Truck Tow Test [Volume 36, Issue 1, 2024, Pages 25-40]
Riblet Numerical Investigation of Drag Reduction Mechanism in Laminar Flow Regime using Rectangular Riblets [Volume 31, Issue 1, 2020, Pages 165-173]
Robotic gripper Design a shape-shifting robot gripper with granular material [Volume 25, Issue 2, 2013, Pages 33-46]
Robot synthesis Implementation of Gibbs-Appell method in dynamic analysis of a novel serial-parallel hybrid robot PP-(3RSS-PS) [Volume 36, Issue 1, 2024, Pages 77-92]
Robust-adaptive Sliding mode control Robust-Adaptive Sliding Mode Controller Design with Fault tolerance for Active Suspension of Half-car model [Volume 34, Issue 3, 2022, Pages 79-96]
Roll forming Theoretical Solution of Linear Hardening Elastic-plastic Deformation Length for a Roll Formed Channel [Volume 24, Issue 1, 2012, Pages 19-32]
Roll forming Experimental Study of the Roll Forming of PVC / Glass Fabric Composite Laminates [Volume 28, Issue 2, 2017, Pages 21-34]
Roll forming Formability Study in Roll Forming Process: Insights into the Influence of Process Parameters on Damage Distribution [(Articles in Press)]
Rotational speed Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
Rubber Improving Optical Quality of Poly methyl methacrylate Sheet by Forming with Rubber [Volume 29, Issue 1, 2017, Pages 1-16]

S

Sail Experimental Investigation of the Sail Position of a Submarine on the Downstream Flow Field [Volume 27, Issue 1, 2016, Pages 71-86]
Sandwich Beam Model Application of SSPH Method in Free Vibration Analysis of Graphene [Volume 31, Issue 2, 2020, Pages 53-66]
Sandwich Panel Experimental and Numerical Investigation on Concrete Specimens with Expanded Metal Sheet under Impact Loading [Volume 32, Issue 1, 2020-2021, Pages 211-230]
Sandwich Panel Free vibration analysis of sandwich panel plate with FML face sheet and flexible core using third-order shear deformation theory [Volume 34, Issue 4, 2022, Pages 1-18]
SA & Taguchi Optimization Superficial Hardening of AISI1045 Steel in High Efficiency Deep Grinding Through Optimization Approaches, Taguchi Method and SA Algorithm [Volume 24, Issue 1, 2012, Pages 87-102]
Scaling Scaling of a Radial Turbine for Turbocharger of a Lean Combustion Engine [Volume 32, Issue 2, 2020-2021, Pages 165-180]
Sealing Effect of Sealing Position on Bulge Height in Hydroforming of Aluminum Tubes [Volume 29, Issue 1, 2017, Pages 81-96]
Segmental Baffle" Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Self-contact concrete Experimental and Numerical Investigation on Concrete Specimens with Expanded Metal Sheet under Impact Loading [Volume 32, Issue 1, 2020-2021, Pages 211-230]
Serpenoid Curve Kinematics and Dynamics of a Snake Robot with Worm Like Locomotion on Inclined Surface [Volume 24, Issue 1, 2012, Pages 71-86]
Shaking force Complete Dynamic Shaking Force Balancing of a 3(RPSP)-S Spherical Parallel Robot Using Extra Linkage [Volume 29, Issue 2, 2017, Pages 145-156]
Shear Improved Smagorinsky Model Numerical Investigation of Particle Deposition in a Room using Large Eddy Simulation based on Lattice Boltzmann Method [Volume 30, Issue 2, 2018, Pages 83-94]
Shell and Tube Heat Exchanger" Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Shock acceleration Experimental and Numerical Analysis of Single and Double layered Aluminum Sheet 3105 With Mechanical Joints under Drop Weight Impact [Volume 30, Issue 2, 2018, Pages 109-123]
Shooting Method An Improved Shooting Method for a Class of Switching Optimal Control Problems [Volume 31, Issue 1, 2020, Pages 123-138]
Side Wind Numerical Verification of the Effect of Side Wind on Fire of the Staircase of a Tall Building With Pyrosim Software [(Articles in Press)]
Signal processing A Novel Method to Improve Crack Detection Ability in Helical Gear [Volume 31, Issue 1, 2020, Pages 1-12]
Silicon The Effect of Interatomic Potential Function on Nanometric Machining of Single Crystal Silicon [Volume 30, Issue 2, 2018, Pages 17-32]
Similarity Solution Natural Convection in a Porous Medium with Heat Generation: Self-Similar Solution [Volume 24, Issue 2, 2012, Pages 45-56]
Similarity Solution Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Simplified model Bending Collapse of Thin Walled Energy Absorber and Presenting Numerical Simplified Model [Volume 26, Issue 2, 2015, Pages 119-128]
Simulated Annealing Algorithm Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method [Volume 28, Issue 1, 2017, Pages 123-131]
Single-phase model Comparison between Single-Phase, Two-Phase Mixture and Eulerian-Eulerian Models for the Simulation of Jet Impingement of Nanofluids [Volume 27, Issue 2, 2016, Pages 55-70]
Single Slotted Flaps Numerical Study of Improving the Aerodynamic Performance of the High Lift Devices in the Two-Element Airfoil [Volume 35, Issue 1, 2023, Pages 37-52]
Sinusoidal vortex generators Investigating the Effect of Angle and Length of Vortex Generators with Sinusoidal Structure on Compact Heat Exchangers Performance [(Articles in Press)]
Sinusoidal Waveform Numerical Simulation of the Effects of Sinusoidal Pulsed Impinging Jet on Heat Transfer from the Concave Cylindrical Surface [Volume 29, Issue 1, 2017, Pages 17-30]
Slip Coefficient Numerical study of forced convection in a microchannel in the presence of nanofluid using the slip condition [Volume 34, Issue 4, 2022, Pages 53-64]
Slip condition Investigation of Slip Condition in the Elastohydrodynamic Lubrication [(Articles in Press)]
Slip velocity Simulation of the Forced Convection Heat Transfer Non-Newtonian Nanofluid, Aqueous Solution of Carboxymethyl Cellulose-Aluminum Oxide, in Slip Flow Regime Through a Microtube [Volume 28, Issue 1, 2017, Pages 47-62]
Small Scale Resistance Spot Welding Investigating the Effect of Film in SSRSW of Hastelloy X Superalloy [Volume 30, Issue 1, 2018, Pages 129-140]
Smoke Movement Numerical Verification of the Effect of Side Wind on Fire of the Staircase of a Tall Building With Pyrosim Software [(Articles in Press)]
Smoke Temperature Numerical Verification of the Effect of Side Wind on Fire of the Staircase of a Tall Building With Pyrosim Software [(Articles in Press)]
Snake Robot Kinematics and Dynamics of a Snake Robot with Worm Like Locomotion on Inclined Surface [Volume 24, Issue 1, 2012, Pages 71-86]
Snake Robot Application of Reinforcement Learning for Navigation of a Planar Snake Robot in Serpentine Locomotion [Volume 26, Issue 1, 2015, Pages 97-118]
Solar Cell Parameter Optimization of Various Solar Cell Models by Neural Network Algorithm [Volume 36, Issue 1, 2024, Pages 123-142]
Solar collector Feasibility of the performance of thermal photovoltaic systems in residential units in the climate of four cities of Abadan, Baghdad, Basra, and Tehran in terms of energy saving. [Volume 35, Issue 3, 2023, Pages 33-50]
Solar desalination؛ absorbent form؛ Solar energy Numerical investigation of the influence of the geometrical shape of the absorber of a single-slope solar desalination device [(Articles in Press)]
Solar energy Thermo-Economic evaluation of a solar dryer with evacuated heat pipe collector and energy storage [Volume 32, Issue 1, 2020-2021, Pages 39-58]
Solar energy Experimental study and numerical modeling of the effect of utilizing selected twisted tape insert on the performance of thermal photovoltaic system [Volume 33, Issue 2, 2021, Pages 1-22]
Solar energy Thermofluid Numerical simulation of the flat solar heating transpired collector for drying purposes [Volume 34, Issue 1, 2022, Pages 61-80]
Solar energy Evaluation of an integrated solar-geothermal energy system to provide power, heat and cooling [Volume 34, Issue 4, 2022, Pages 19-34]
Solar energy Design, construction and experimental investigation of parabolic solar cooker performance [Volume 36, Issue 1, 2024, Pages 93-106]
Solar power tower Numerical Study of Flow and Heat Transfer in Cavity Receiver Tube of a Solar Power Tower with Different Inserts under Non-uniform Heat flux [Volume 35, Issue 2, 2023, Pages 17-36]
Solar radiation Effect of Air Gap between two Glass Covers on the Performance of Plane Solar Air Heaters [Volume 33, Issue 2, 2021, Pages 55-82]
Solar radiation Estimation of solar radiation in different climates of Iran using hybrid machine learning methods [Volume 35, Issue 2, 2023, Pages 37-54]
Space Payload Recovery Derivation of Aerodynamic Characteristics of a Ribbon Parachute by Truck Tow Test [Volume 36, Issue 1, 2024, Pages 25-40]
Spacer Grid Numerical Model Development of Dummy Fuel Rod Under New Spacer Grids and End Constraints Using Experimental Modal Analysis [Volume 34, Issue 4, 2022, Pages 89-104]
Specularity Coefficient Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Spherically Symmetric Illumination Thermal Radiation Heat Transfer Effects on Single Fuel Droplet Heat up Considering it’s Internal Circulation [Volume 23, Issue 1, 2012, Pages 67-82]
Spherical parallel robot Complete Dynamic Shaking Force Balancing of a 3(RPSP)-S Spherical Parallel Robot Using Extra Linkage [Volume 29, Issue 2, 2017, Pages 145-156]
Spherical Robot Nonlinear Control of Motion of A Spherical Robot on Inclined Surfaces Based on Feedback Linearization Method [Volume 31, Issue 2, 2020, Pages 91-104]
Spinning Feed effect on strain and stress in dome forming (spinning) of a tube in an aluminum CNG vessel manufacturing [Volume 32, Issue 2, 2020-2021, Pages 43-60]
Spur gear Spur Gear Profile Modification for the Reduction of Static Transmission Error [Volume 29, Issue 2, 2017, Pages 129-144]
Square bluff body Experimental Investigation on Flow Downstream of a Square Bluff Body at Different Angles [Volume 31, Issue 2, 2020, Pages 177-187]
Square cross-section Simulation of Particle Motion in Non-Newtonian Fluids by Immersed Boundary Lattice Boltzmann Method [Volume 28, Issue 1, 2017, Pages 75-92]
Square cylinder Numerical Investigation of Flow Induced Sound Around a Square Cylinder at Various Incidence Angles [Volume 28, Issue 2, 2017, Pages 97-114]
Square geometry Applying Suction and Blowing Flow Control Approaches to Reduce the Flow-induced Instabilities of Elastically-mounted Square Cylinder [Volume 34, Issue 2, 2022, Pages 29-44]
SSPH Method Application of SSPH Method in Free Vibration Analysis of Graphene [Volume 31, Issue 2, 2020, Pages 53-66]
Stability analysis Dynamic Stability Analysis of Rectangular Mindlin Plate in Contact with Fluid under Passage of Oscillating Rigid Bodies [Volume 34, Issue 4, 2022, Pages 65-88]
Stable Circular Jump A Phenomenological Study of Polygonal Hydraulic Jumps [Volume 31, Issue 1, 2020, Pages 87-104]
Stable Droplet Modeling of a Stable Droplet Suspended in Vapor by Lattice Boltzmann Method [Volume 27, Issue 1, 2016, Pages 153-162]
Stagnation point flow Similarity Solution of Axisymmetric Stagnation Point Flow of Nanofluid on Rotating Cylinder [Volume 29, Issue 2, 2017, Pages 57-70]
Stainless steel AISI420 Optimization of Hardening Heat treatment of Oil Extraction Machine’s Cylinder Made of Stainless steel [(Articles in Press)]
Stamping process Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell [(Articles in Press)]
Standing Surface Acoustic Waves Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
State of Charge Electrochemical-Thermal Simulation of Cell Lithium-Ion Battery of Electrical Vehicle [Volume 31, Issue 2, 2020, Pages 33-52]
Static analysis of beams Reliability Analysis of Beams with both Random Material Properties and Random Loading Conditions [Volume 24, Issue 1, 2012, Pages 1-18]
Statistical properties Study of entropy generation and evaluation statistical heat transfer properties in turbulent flow [Volume 29, Issue 1, 2017, Pages 63-80]
Steam Power Plant Multi Objective Optimization of Converting an Old Steam Power Plant to Combined Cycle Power Plant (CCPP) Using Double and Single Pressure Heat Recovery Steam Generator (HRSG) via Genetic Algorithm [Volume 27, Issue 2, 2016, Pages 129-139]
Step Over Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
STM32 board Identification of electromagnetic linear motor parameters in order to generate inertial force using ARM microcontroller [Volume 34, Issue 2, 2022, Pages 87-98]
Stochastic Finite Element Stability and Free Vibration Analysis of Plates with Random Material Property using Stochastic Finite Element Method [Volume 30, Issue 2, 2018, Pages 151-160]
Stress integration Different Methods to Compute Force over a Cylinder by LBM [Volume 25, Issue 1, 2013, Pages 114-123]
Stress Recovery Effect of Superconvergent Stress Points for Solution Improvement and Error Estimation of Isogeometric Analysis of Axisymmetric Problems [Volume 26, Issue 1, 2015, Pages 79-95]
Stress Recovery Improvement of Stress and Error Estimation by Patch Equilibrium in Isogeometric Analysisic analysis [Volume 26, Issue 2, 2015, Pages 73-87]
Stress updating Verification of Quarter-step Exponential Map Method for Integration of Von-Mises Plasticity [Volume 30, Issue 1, 2018, Pages 17-30]
Strouhal number Experimental study of measurement of free oscillations of a cylinder with fin in wind tunnel under different Reynolds [Volume 35, Issue 4, 2023, Pages 47-62]
Submarine model Experimental Investigation of the Sail Position of a Submarine on the Downstream Flow Field [Volume 27, Issue 1, 2016, Pages 71-86]
Suction Optimization of Suction Jet Length on NACA 0012 Airfoil with Using of Reynolds Stress Model (RSM) [Volume 25, Issue 1, 2013, Pages 61-76]
Suction Amplitude Optimization of Suction Jet Length on NACA 0012 Airfoil with Using of Reynolds Stress Model (RSM) [Volume 25, Issue 1, 2013, Pages 61-76]
Suction and Injection Natural Convection in a Porous Medium with Heat Generation: Self-Similar Solution [Volume 24, Issue 2, 2012, Pages 45-56]
Suction jet Investigation of Suction Jet Parameters in Flow Control of Dynamic Stall [Volume 32, Issue 2, 2020-2021, Pages 181-200]
Suction Jet Length Optimization of Suction Jet Length on NACA 0012 Airfoil with Using of Reynolds Stress Model (RSM) [Volume 25, Issue 1, 2013, Pages 61-76]
Sudden expansion Simulation of nanofluid flow at low Reynolds number in a microchannel with one-sided sudden expansion under the effect of a magnetic field [Volume 35, Issue 3, 2023, Pages 85-100]
Supercritical boiler Numerical simulation of turbulent heat transfer in boiler with supercritical fluid and asymmetric thermal conditions [(Articles in Press)]
Superficial Hardening Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
Supersonic Flow Experimental Investigation of the Influence of Transverse Dual protuberances on the Thrust Vector of a Supersonic C-D nozzle [Volume 31, Issue 1, 2020, Pages 139-154]
Supersonic Turbine Experimental and Numerical Study of Partial Admission Effect on Flow Distribution in Supersonic Turbine Axial-Gap [Volume 24, Issue 2, 2012, Pages 17-32]
Supersonic Turbine Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Support vector machine Automated Fault Detection of Tri-Lobe Compressor Using Wavelet Transformation and Support Vector Machine [Volume 27, Issue 1, 2016, Pages 19-34]
Surface profile Study on the effects of ball burnishing parameters and initial surface roughness on the core roughness characteristics of Copper cylindrical parts [Volume 32, Issue 2, 2020-2021, Pages 113-132]
Surface Roughness Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
Surface Roughness Experimental Determination of HT29 Cancerous Cell Surface Roughness by Atomic Force Microscopy to be Applied in Nanomanipulation [Volume 28, Issue 1, 2017, Pages 111-122]
Surface Roughness Study on the effects of ball burnishing parameters and initial surface roughness on the core roughness characteristics of Copper cylindrical parts [Volume 32, Issue 2, 2020-2021, Pages 113-132]
Surface Temperature Study of Microstructure and Grain Size Effect on Superficial Hardening of AISI1045 within High Efficiency Deep Grinding [Volume 26, Issue 2, 2015, Pages 89-105]
Surface Temperature Numerical Study of the Effects of Structural and Functional Parameters on Unmixed Combustion of Natural Gas in Three Radiant Tubes with Different Geometries [Volume 33, Issue 2, 2021, Pages 83-92]
Swirl direction Numerical Simulation of Toos Power Plant Boiler to Improve its Thermal Efficiency [Volume 27, Issue 1, 2016, Pages 117-134]
Switching Optimal Control An Improved Shooting Method for a Class of Switching Optimal Control Problems [Volume 31, Issue 1, 2020, Pages 123-138]
Symmetric aero-foil blades Parametric study and numerical analysis of the regenerative compressor with symmetric aerodynamic blades, to improve performance [Volume 32, Issue 2, 2020-2021, Pages 1-18]
Symmetric Balanced Hybrid Composite Multi-objective Optimization of Hybrid Laminated Composites under a Frequency Constraint by Using the Particle Swarm Optimization [Volume 24, Issue 2, 2012, Pages 97-113]
System Identification Identification of electromagnetic linear motor parameters in order to generate inertial force using ARM microcontroller [Volume 34, Issue 2, 2022, Pages 87-98]

T

Taguchi method Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel [Volume 23, Issue 2, 2012, Pages 99-110]
Taguchi method Heat Transfer of Nanofluid in a Channel with Magnetic Field and Porous Obstacle using the Darcy-Brinkman-Forchheimer Model in the LBM Method [Volume 32, Issue 1, 2020-2021, Pages 153-172]
Taguchi technique Analysis of Forming Parameters in Sheet Hydro-Forming Process [Volume 24, Issue 1, 2012, Pages 33-52]
Tailor Welded Blank (TWB) Investigation of Forming Limit and Weld Line Movement in the Forming of Tailor Welded Blanks using Experiment and Numerical Methods [Volume 23, Issue 2, 2012, Pages 1-16]
Tailor-Welded Blank (TWB) Effect of Fluid Pressure on Weld-Line Movement and Thickness Distribution in Hydro-Mechanical Deep Drawing of Tailor-Welded Blanks (TWBs) [Volume 23, Issue 1, 2012, Pages 53-66]
Tapered Euler- Bernoulli beam Free Vibration Analysis of Functionally Graded Rotating Double Tapered Beam by using Euler-bernoulli Beam Theory and Differential Transform Method [Volume 27, Issue 1, 2016, Pages 51-70]
Temperature Gradient Numerical Simulation of Crack Growth in the Glass Layer of Gallium-Arsenide Solar Cell [Volume 33, Issue 2, 2021, Pages 93-104]
Temperature jump Simulation of the Forced Convection Heat Transfer Non-Newtonian Nanofluid, Aqueous Solution of Carboxymethyl Cellulose-Aluminum Oxide, in Slip Flow Regime Through a Microtube [Volume 28, Issue 1, 2017, Pages 47-62]
Thermal Analysis Numerical and Experimental Investigation on the Parabolic Dish SolarConcentrator [Volume 32, Issue 1, 2020-2021, Pages 17-38]
Thermal comfort Investigation of Down-Draught Effect on The Thermal Comfort Indexes in The Building With Glazing Envelope [Volume 33, Issue 1, 2021, Pages 35-52]
Thermal comfort Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings [Volume 34, Issue 4, 2022, Pages 35-52]
Thermal Development Numerical study of forced convection in a microchannel in the presence of nanofluid using the slip condition [Volume 34, Issue 4, 2022, Pages 53-64]
Thermal dispersion Numerical and Analytical Investigation of Thermal Dispersion Effects on the Heat Transfer of Nanofluid flow inside a Channel [Volume 29, Issue 2, 2017, Pages 21-40]
Thermal efficiency Thermofluid Numerical simulation of the flat solar heating transpired collector for drying purposes [Volume 34, Issue 1, 2022, Pages 61-80]
Thermal massflowmeter Designing and Numerical Analysis of Capillary Tube Thermal Mass Flowmeter as a Residential Natural Gas Meter [Volume 29, Issue 1, 2017, Pages 49-62]
Thermal Moment Electrostatically Actuated FGM Microgripper under the Effect of Thermal Moment [Volume 23, Issue 2, 2012, Pages 65-80]
Thermal performance Thermal Performance Analysis of Natural Draft Dry Cooling Towers Based on New Theoretical Method [Volume 32, Issue 1, 2020-2021, Pages 191-210]
Thermal performance Effect of Air Gap between two Glass Covers on the Performance of Plane Solar Air Heaters [Volume 33, Issue 2, 2021, Pages 55-82]
Thermofluid numerical Thermofluid Numerical simulation of the flat solar heating transpired collector for drying purposes [Volume 34, Issue 1, 2022, Pages 61-80]
Thermoforming Improving Optical Quality of Poly methyl methacrylate Sheet by Forming with Rubber [Volume 29, Issue 1, 2017, Pages 1-16]
Thermo-hydraulic" Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Thermophysical properties Numerical simulation of turbulent heat transfer in boiler with supercritical fluid and asymmetric thermal conditions [(Articles in Press)]
The Statistics of Kolmogorov-Smirnov The Friction Factor of Turbulent Flow of the Base Fluid and Nanofluid in the Statistical Approach [Volume 31, Issue 1, 2020, Pages 105-122]
Thickness Effect of Sealing Position on Bulge Height in Hydroforming of Aluminum Tubes [Volume 29, Issue 1, 2017, Pages 81-96]
Thickness Investigating the Effect of Polymer Membrane Characteristics on the Performance of the Membrane Humidifier [Volume 35, Issue 4, 2023, Pages 17-32]
Thickness Distribution Effect of Fluid Pressure on Weld-Line Movement and Thickness Distribution in Hydro-Mechanical Deep Drawing of Tailor-Welded Blanks (TWBs) [Volume 23, Issue 1, 2012, Pages 53-66]
Thickness Distribution Experimental Study and Simulation of Tube Hydroforming Process of Bi-layered Aluminum-Copper with Axial Feeding [Volume 28, Issue 2, 2017, Pages 65-84]
Thickness Distribution Experimental and Numerical Investigation of Pressure-Induced Changes in Tube Thickness Distribution and Cross-Section during Rotary Bending [(Articles in Press)]
Thin bending plate The Effect of Equilibrium Equation and Trefftz Functions on the Responses of Quadrilateral Bending Plate [Volume 29, Issue 2, 2017, Pages 99-118]
Thin walled beam theory Investigation of the Effect of Geometrical and Mechanical Properties of Horizontal Wind Turbines on its Dynamic Behavior for Free and Forced Vibration Case [Volume 27, Issue 2, 2016, Pages 113-128]
Thin-walled profiles Numerical study of the effect of geometry and metal foam on the energy absorption of nested profiles [Volume 34, Issue 3, 2022, Pages 67-78]
Third Order Reddy Theory Frequency Analysis of Cracked Porous Functionally Graded Beams on Elastic Foundation using Reddy Third Order Shear Deformation Theory [Volume 32, Issue 2, 2020-2021, Pages 93-112]
Third Order Shear Deformation Theory Vibration of FGM Plates With Distributed Mass Using Third Order Shear Deformation Theory [Volume 26, Issue 2, 2015, Pages 55-71]
Third Order Shear Deformation Theory Nonlinear Forced Vibration of Functionally Graded Magneto-Electro-Elastic Rectangular Plate based on the Third Order Shear Deformation Theory [Volume 30, Issue 2, 2018, Pages 47-66]
Third-Order Shear Deformation Theory Free vibration analysis of sandwich panel plate with FML face sheet and flexible core using third-order shear deformation theory [Volume 34, Issue 4, 2022, Pages 1-18]
Three-Dimensional heat transfer Designing and Numerical Analysis of Capillary Tube Thermal Mass Flowmeter as a Residential Natural Gas Meter [Volume 29, Issue 1, 2017, Pages 49-62]
Thrust-vector angle Numerical Analysis of Fuel Injection Impacts on Thrust-Vectoring in a Dual Throat Nozzle [Volume 33, Issue 1, 2021, Pages 71-92]
Thrust vector control Effects of Divergence Angle on Moveable Nozzle Performance in Thrust Vector Control System [Volume 26, Issue 1, 2015, Pages 1-15]
Thrust-vectoring Numerical Analysis of Fuel Injection Impacts on Thrust-Vectoring in a Dual Throat Nozzle [Volume 33, Issue 1, 2021, Pages 71-92]
Thrust-vectoring efficiency Numerical Analysis of Fuel Injection Impacts on Thrust-Vectoring in a Dual Throat Nozzle [Volume 33, Issue 1, 2021, Pages 71-92]
Tibia Bone Investigating the Effect of Tibia Bone Heterogeneity on Natural Frequency Using Modal Test and Finite Element Modeling [Volume 35, Issue 2, 2023, Pages 77-96]
Tilt and Mount Angles Hydrodynamic Analysis of Circular and Non-Circular Journal Bearings Using Generalized Differential Quadrature Method [Volume 23, Issue 1, 2012, Pages 97-112]
Time Dependent Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Time Periodic Flow Application of Adaptive Time Spectral Method to Analyze Inviscid Compressible Flow Around a Pitching Airfoil [Volume 35, Issue 1, 2023, Pages 1-18]
Time Spectral Method Periodic Unsteady Transonic Compressible Flow Simulation using Fourier-Based Algorithm [Volume 25, Issue 2, 2013, Pages 47-64]
Time Spectral Method Application of Adaptive Time Spectral Method to Analyze Inviscid Compressible Flow Around a Pitching Airfoil [Volume 35, Issue 1, 2023, Pages 1-18]
Titanium bipolar plates Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell [(Articles in Press)]
Tool geometry Simultaneous Optimization of Machining Parameters and Tool Geometry Specifications in Turning Operation of AISI1045 Steel [Volume 23, Issue 2, 2012, Pages 99-110]
Tool polarity The Study of the Effect of Input Parameters on Material Romoval Rate, %Tool Water Ratio and Surface Roughness of AISI H13 Tool Steel in the Electrical Discharge Machining (EDM) [Volume 24, Issue 1, 2012, Pages 123-132]
Total annual cost Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Tow dimensional vibration tool One And Two Dimensional Ultrasonic Vibration Tool [Volume 26, Issue 1, 2015, Pages 35-50]
TPU Investigating the mechanical properties of polymer composite materials made by 3D printing method [Volume 35, Issue 4, 2023, Pages 77-89]
Transmission and Supply pipelines Presenting a Correlation to Obtain Natural Gas Leakage Rate from a Buried High-Pressure Pipeline in a Porous Media [Volume 32, Issue 1, 2020-2021, Pages 231-254]
Transmission Error Spur Gear Profile Modification for the Reduction of Static Transmission Error [Volume 29, Issue 2, 2017, Pages 129-144]
Transmission Error A Novel Method to Improve Crack Detection Ability in Helical Gear [Volume 31, Issue 1, 2020, Pages 1-12]
Traveling Surface Acoustic Waves Numerical Simulation of Same-sized Cells Focusing and Separation with Surface Acoustic Waves [Volume 32, Issue 1, 2020-2021, Pages 77-92]
Trefftz function The Effect of Equilibrium Equation and Trefftz Functions on the Responses of Quadrilateral Bending Plate [Volume 29, Issue 2, 2017, Pages 99-118]
Trefoil baffle" Numerical comparison of shell side thermo-hydraulic characteristics of shell and tube heat exchangers with trefoil and segmental baffle by genetic algorithm [Volume 35, Issue 2, 2023, Pages 55-76]
Tridiagonal system of equations Parallel Thomas Approach in Computational Fluid Dynamics with GPUs- Lid-driven Cavity [Volume 28, Issue 2, 2017, Pages 152-164]
Tri-lobe compressor Automated Fault Detection of Tri-Lobe Compressor Using Wavelet Transformation and Support Vector Machine [Volume 27, Issue 1, 2016, Pages 19-34]
Truck Tow Test Derivation of Aerodynamic Characteristics of a Ribbon Parachute by Truck Tow Test [Volume 36, Issue 1, 2024, Pages 25-40]
Tube bending simulation Experimental and Numerical Investigation of Pressure-Induced Changes in Tube Thickness Distribution and Cross-Section during Rotary Bending [(Articles in Press)]
Tube hydroforming Prediction of Forming Limit Curve Using Ductile Fracture Criteria in Hydrofoming of Aluminum Tubes [Volume 25, Issue 1, 2013, Pages 17-28]
Tube hydroforming Experimental Study and Simulation of Tube Hydroforming Process of Bi-layered Aluminum-Copper with Axial Feeding [Volume 28, Issue 2, 2017, Pages 65-84]
Tube hydroforming Effect of Sealing Position on Bulge Height in Hydroforming of Aluminum Tubes [Volume 29, Issue 1, 2017, Pages 81-96]
Tube spring back Experimental investigation and Numerical simulation of bending parameters on the spring back of the tube in the rotational bending process [(Articles in Press)]
Tufting Design of an ejector in carpet industry by the method of Tufting [Volume 29, Issue 1, 2017, Pages 123-132]
Turbine Characteristic Map Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Turbine Test Rig Experimental Evaluation of Supersonic Turbine Characteristic Curve at Full and Partial Admission in Turbine Test Rig [Volume 28, Issue 2, 2017, Pages 1-20]
Turbocharger Scaling of a Radial Turbine for Turbocharger of a Lean Combustion Engine [Volume 32, Issue 2, 2020-2021, Pages 165-180]
Turbofan Engines Simulation of the Secondary Combustion Chamber Application of Turbofan Engine in Off-design Point [Volume 29, Issue 2, 2017, Pages 1-20]
Turbulence model Accelerated Turbulent Pipe Flow Study using Various Turbulence Models [Volume 27, Issue 2, 2016, Pages 11-28]
Turbulence shear stress Accelerated Turbulent Pipe Flow Study using Various Turbulence Models [Volume 27, Issue 2, 2016, Pages 11-28]
Turbulent Flow Numerical Simulation of the Effect of the Location of Impinging Jets on the Convective Heat Transfer from a Cylindrical Concave Surface [Volume 27, Issue 2, 2016, Pages 71-86]
Turbulent Flow Numerical Simulation of the Effects of Sinusoidal Pulsed Impinging Jet on Heat Transfer from the Concave Cylindrical Surface [Volume 29, Issue 1, 2017, Pages 17-30]
Turbulent Flow Nanoparticle Shape Effect on a Nanofluid-Based Parabolic Trough Concentrating Photovoltaic/Thermal System [Volume 29, Issue 2, 2017, Pages 41-56]
Turbulent Flow Large-Eddy Simulation of Turbulent Square Duct Flow [Volume 31, Issue 1, 2020, Pages 13-22]
Turbulent Flow The Friction Factor of Turbulent Flow of the Base Fluid and Nanofluid in the Statistical Approach [Volume 31, Issue 1, 2020, Pages 105-122]
Turbulent Flow Numerical simulation of inlet velocity and geometry effects of on the hydrodynamics of gas-solid turbulent flow in a fluidized bed reactor [(Articles in Press)]
Turbulent jet Numerical Prediction of Near-field Noise and Return Acoustics from Sonic Jets in Different Operating Conditions [Volume 32, Issue 2, 2020-2021, Pages 19-42]
Turbulent mixing noise Numerical Prediction of Near-field Noise and Return Acoustics from Sonic Jets in Different Operating Conditions [Volume 32, Issue 2, 2020-2021, Pages 19-42]
Turning One And Two Dimensional Ultrasonic Vibration Tool [Volume 26, Issue 1, 2015, Pages 35-50]
TVC Experimental Investigation of the Influence of Transverse Dual protuberances on the Thrust Vector of a Supersonic C-D nozzle [Volume 31, Issue 1, 2020, Pages 139-154]
Twin screw extruder The Study on the Mechanical Properties of the De-Vulcanized Waste Rubber by a Mechanical Technique [Volume 30, Issue 2, 2018, Pages 95-108]
Twist defect Geometry Effects of Asymmetrical Channel Sections on Common Defects in the Roll Forming Process [Volume 30, Issue 2, 2018, Pages 1-16]
Twist Drilling Study of the Effect of Machining Parameters on Drilling of Composite Materials and Monitoring of Process by Acoustic Emission [Volume 24, Issue 2, 2012, Pages 1-16]
Two-phase Flow Improving the gas flow distribution in a PEMFC stack by removing liquid water from the manifold [Volume 34, Issue 3, 2022, Pages 1-14]
Two-phase mixture model Comparison between Single-Phase, Two-Phase Mixture and Eulerian-Eulerian Models for the Simulation of Jet Impingement of Nanofluids [Volume 27, Issue 2, 2016, Pages 55-70]
Two Phase System Modeling of a Stable Droplet Suspended in Vapor by Lattice Boltzmann Method [Volume 27, Issue 1, 2016, Pages 153-162]
T-Y micromixer Numerical simulation of viscoelastic fluid mixing in a T-Y shaped micromixer [(Articles in Press)]

U

Ultrasonic One And Two Dimensional Ultrasonic Vibration Tool [Volume 26, Issue 1, 2015, Pages 35-50]
Ultrasonic Vibration drilling tool and thrust force investigation in vibratory drilling process of Al 2024-T6 [Volume 26, Issue 1, 2015, Pages 129-142]
Ultrasound Finite Element Modeling of Laser Ultrasonics Process in Thermoelastic Regime [Volume 32, Issue 1, 2020-2021, Pages 133-152]
Uncertainties Analysis Statistical Analysis of Piezoelectric Energy Harvesting in the Bridge Systems [Volume 28, Issue 1, 2017, Pages 31-46]
Uncertainty Robust-Adaptive Sliding Mode Controller Design with Fault tolerance for Active Suspension of Half-car model [Volume 34, Issue 3, 2022, Pages 79-96]
Unglazed transpired flat plate solar collector Thermofluid Numerical simulation of the flat solar heating transpired collector for drying purposes [Volume 34, Issue 1, 2022, Pages 61-80]
Uniform and non-uniform magnetic field Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
Uniform distribution of force. Energy consumption Effect of Flower Pattern on Uniform Distribution of Force on Rollers in Reshaping of Cold Roll Forming [Volume 34, Issue 1, 2022, Pages 49-60]
Uniform heat absorption/production Non Newtonian conjugate heat transfer under the impact of uniform and non-uniform magnetic field along with heat absorption/production inside a two-dimensional chamber containing a block at different temperatures; An entropy analysis with LBM [Volume 34, Issue 3, 2022, Pages 35-66]
Uniform Heat Flux A Study of the Effect of Curvature of the Corner of Hole on Stress Concentration Caused by Uniform Heat Flux [Volume 28, Issue 1, 2017, Pages 63-74]
Unsteady flow Investigation of the impact of blowing jet on the dynamic stall of NACA0012 [Volume 34, Issue 1, 2022, Pages 1-20]
Unsteady flow Experimental study of measurement of free oscillations of a cylinder with fin in wind tunnel under different Reynolds [Volume 35, Issue 4, 2023, Pages 47-62]
Unsteady transonic flow Periodic Unsteady Transonic Compressible Flow Simulation using Fourier-Based Algorithm [Volume 25, Issue 2, 2013, Pages 47-64]
Unstructured Grid Numerical Study of Improving the Aerodynamic Performance of the High Lift Devices in the Two-Element Airfoil [Volume 35, Issue 1, 2023, Pages 37-52]

V

Vaporization Rate Thermal Radiation Heat Transfer Effects on Single Fuel Droplet Heat up Considering it’s Internal Circulation [Volume 23, Issue 1, 2012, Pages 67-82]
Variable Pitch Quadrotor Variable-Pitch Control of a Quadrotor Using Feedback Linearization Controller and Direct Adaptive Feedback Linearization Controller [Volume 31, Issue 2, 2020, Pages 67-90]
Variable radius die Experimental investigation and Numerical simulation of bending parameters on the spring back of the tube in the rotational bending process [(Articles in Press)]
Variable Span Aerodynamic Performance Investigation of an Experimental Variable-Span Morphing Wing Model [Volume 27, Issue 1, 2016, Pages 35-50]
Vehicle-Bridge Vibration Statistical Analysis of Piezoelectric Energy Harvesting in the Bridge Systems [Volume 28, Issue 1, 2017, Pages 31-46]
Vehicle dynamic An Investigation on the Effects of Geometric and Dynamic Parameters on the Truck Lateral Deviation Due to the Braking Force Imbalance [Volume 26, Issue 2, 2015, Pages 141-152]
Vehicle Dynamics Theoretical and Experimental Investigation on the Vehicle Lateral Deviation Due to the Braking Force Error [Volume 23, Issue 1, 2012, Pages 41-52]
Vibration Effects of Gyroscopic Moment on the Dynamics and Vibrations of a High- Speed Double- Helical Gear Pair [Volume 29, Issue 1, 2017, Pages 31-48]
Vibration analysis Introducing a New Crack Disturbance Function for Transverse Vibration Analysis of a Cracked Beam [Volume 25, Issue 2, 2013, Pages 19-32]
Vibration cutting (VC) Vibration Cutting and Elliptical Ultrasonic Vibration Assisted Turning of In738 Work-Pieces [Volume 23, Issue 2, 2012, Pages 17-28]
Vibrations The Electric Response of Piezoelectric Beam Using Dynamic Stiffness Method [Volume 31, Issue 2, 2020, Pages 127-140]
Vibration tool One And Two Dimensional Ultrasonic Vibration Tool [Volume 26, Issue 1, 2015, Pages 35-50]
Vibratory Drilling Vibration drilling tool and thrust force investigation in vibratory drilling process of Al 2024-T6 [Volume 26, Issue 1, 2015, Pages 129-142]
Viscoelastic Flow Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Viscoelastic fluid Numerical simulation of viscoelastic fluid mixing in a T-Y shaped micromixer [(Articles in Press)]
Volume Fraction Laminate Free vibration analysis of sandwich panel plate with FML face sheet and flexible core using third-order shear deformation theory [Volume 34, Issue 4, 2022, Pages 1-18]
Volute Experimental and Numerical Flow Investigation through a Radial Flow Compressor Volute [Volume 28, Issue 1, 2017, Pages 1-14]
Von Kármán Numerical Investigation of Transient Laminar Flow of a Giesekus Viscoelastic Fluid around a Circular Cylinder [Volume 24, Issue 2, 2012, Pages 67-80]
Vortex flowmeter Experimental Investigation on Flow Downstream of a Square Bluff Body at Different Angles [Volume 31, Issue 2, 2020, Pages 177-187]
Vortex Generator Numerical analysis of the obstacle effect with different geometry on the heat transfer of nanofluid flow in a rectangular channel [Volume 35, Issue 3, 2023, Pages 51-64]
Vortex Generator Investigation on the effect of using vortex generator in the flow path of combustion product in the chimney of a natural gas wall-mounted water heater on flow hydrodynamics and improving heat transfer [(Articles in Press)]
Vortex-Induced Vibration VIV control in the flow over a cylinder using axial magnetic field [Volume 35, Issue 1, 2023, Pages 87-106]
Vortex Shedding Experimental Investigation on Flow Downstream of a Square Bluff Body at Different Angles [Volume 31, Issue 2, 2020, Pages 177-187]
Vortex Shedding Applying Suction and Blowing Flow Control Approaches to Reduce the Flow-induced Instabilities of Elastically-mounted Square Cylinder [Volume 34, Issue 2, 2022, Pages 29-44]
V-shaped cantilevers Experimental and Theoretical Investigation of Young's Modulus of Breast Cancer Tissue (MCF-10) Using Different Cantilevers of Atomic Force Microscope [Volume 36, Issue 1, 2024, Pages 61-76]
Vulcanization Simulation of Rubber Vulcanization for Calculation of the Curing Time with Modification of the Kinetic Model [Volume 26, Issue 2, 2015, Pages 107-118]

W

Walking Dynamic Modeling and Optimal Walking Gait Planning of a Real Biped Robot Based on SLIP and Compass gait Models [Volume 30, Issue 1, 2018, Pages 31-50]
Wall Boundary Condition for solid Phase Numerical Analysis of the Hydrodynamic Behavior of Three-Phase Mixing of Rice Husk, Sand and Air in a Bubbling Fluidized Bed with Particle Granular Behavior [Volume 34, Issue 2, 2022, Pages 61-86]
Water hammer problem .Numerical Modelling of Water Hammer Problems based on the Flux Wave Approach and Baldwin-Lomax Turbulence Model [Volume 29, Issue 1, 2017, Pages 97-110]
Water jet breakup Experimental Investigation of Breakup Characteristics of Elliptical, Rectangular and Circular Water Jets [Volume 30, Issue 1, 2018, Pages 1-16]
Water removal Improving the gas flow distribution in a PEMFC stack by removing liquid water from the manifold [Volume 34, Issue 3, 2022, Pages 1-14]
Wavelet Analysis Study of the Effect of Machining Parameters on Drilling of Composite Materials and Monitoring of Process by Acoustic Emission [Volume 24, Issue 2, 2012, Pages 1-16]
Wave propagation algorithm .Numerical Modelling of Water Hammer Problems based on the Flux Wave Approach and Baldwin-Lomax Turbulence Model [Volume 29, Issue 1, 2017, Pages 97-110]
Weissenberg number Numerical simulation of viscoelastic fluid mixing in a T-Y shaped micromixer [(Articles in Press)]
Welding parameters Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas [(Articles in Press)]
Weld Line Movement Investigation of Forming Limit and Weld Line Movement in the Forming of Tailor Welded Blanks using Experiment and Numerical Methods [Volume 23, Issue 2, 2012, Pages 1-16]
Weld-Line Movement Effect of Fluid Pressure on Weld-Line Movement and Thickness Distribution in Hydro-Mechanical Deep Drawing of Tailor-Welded Blanks (TWBs) [Volume 23, Issue 1, 2012, Pages 53-66]
Wind effects Numerical Investigation of Wind Effects on the Flame Shape of Sarkhoon and Qeshm’s Refinery Flares [Volume 28, Issue 2, 2017, Pages 51-64]
Wind turbine Optimization of hybrid solar/wind/battery system with different prime movers (Diesel engine, Gas engine, Gas turbine) [Volume 32, Issue 2, 2020-2021, Pages 61-76]
Winkler Pasternak Frequency Analysis of Cracked Porous Functionally Graded Beams on Elastic Foundation using Reddy Third Order Shear Deformation Theory [Volume 32, Issue 2, 2020-2021, Pages 93-112]
Wire Cut Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Wire Cut Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Wire Feed Speed Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Wire Feed Speed Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Wire Tension Prediction and Optimization of Mold Steel Hardness in Wire Cut Process Based on Fuzzy Inference System [Volume 35, Issue 1, 2023, Pages 53-70]
Wire Tension Optimization of Dimensional Accuracy of Mold Steel in Wire Cut Process Based on Response Surface Method [Volume 35, Issue 2, 2023, Pages 97-106]
Wolf Optimization Algorithm Estimation of solar radiation in different climates of Iran using hybrid machine learning methods [Volume 35, Issue 2, 2023, Pages 37-54]
Wooden Products Investigating the CNC milling machine parameters and machining tool specifications on surface roughness of wooden products [Volume 35, Issue 3, 2023, Pages 65-74]
Words Compressible Viscous Flow Direct Numerical Simulation of Supersonic and Transonic Compressible Viscous Flow by Kinetic Energy Preserving Scheme [Volume 28, Issue 1, 2017, Pages 15-30]

Y

Yap correction Numerical Simulation of the Effect of the Location of Impinging Jets on the Convective Heat Transfer from a Cylindrical Concave Surface [Volume 27, Issue 2, 2016, Pages 71-86]