Simulation of Rubber Vulcanization for Calculation of the Curing Time with Modification of the Kinetic Model

Document Type : Original Article

Authors

• Mohammad Reza Erfanian ¹
• Seyed Mohammad Javadi ²
• Mohammad Moghiman ³

¹ ferdowsi University of Mashhad

² University of Advanced Technologies Engineering, Quchan

³ Ferdowsi University of Mashhad

10.22067/fum-mech.v26i2.37436

Abstract

The present work is focused on the computational method for simulation of the rubber vulcanization process in injection molding machines. The main innovation of the work is the calculation of the curing time in a rubbery part using the modification of curing kinetic model. For solving the curing equations, the computer code is developed in “UDF” module of the Fluent. The parameters of curing model, specific heat and viscosity of the rubber are obtained from the experiment. In order to evaluate the experimental curing time, a mechanical compression test is performed on the rubbery part at different times. Predicted mold filling and curing times are compared with experimental data, which confirmed the accuracy and applicability of the method.

Keywords

• Numerical simulation
• Vulcanization
• Injection Molding
• Curing Time

---

References

1. Vergnad, J.M. and Rosca, I.D., "Rubber Curing and Properties", CRC Press, Taylor-Francis Group. New York pp. 1-11, (2009).

2. Holm, E.J. and Langtangen, H.P., "A Unified Finite Element Model For The Injection Molding Process", Computer Methods in Applied Mechanics and Engineering, Vol. 178, pp. 413-429, (1999).

3. Ramorino, G., Girardi, M., Agnelli, S. and Franceschini, A., "Injection Molding of Engineering Rubber Components: A Comparison Between Experimental Results and Numerical Simulation", International Journal of Material Forming, Vol. 3, pp. 551-554, (2010).

4. Zhang, P., Zhao, F., Yaun, Y., Shi, X. and Zhao, S., "Network Evolution Based on General-Purpose Diene Rubbers/Sulfur/TBBS System During Vulcanization (I)", Polymer, Vol. 51, pp. 257-263, (2010).

5. Ghoreishy, M.H.R. and Naderi, G., "Three Dimensional Finite Element Modeling of Rubber Curing Process", Journal of Elastomers and Plastics, Vol. 37, pp. 37-53, (2005).

6. Arrillaga, A., Zaldua, A. M.R., Atxurra, M. and Farid, A.S., "Techniques Used For Determining Cure Kinetics of Rubber Compounds", European Polymer Journal, Vol. 43, pp. 4783-4799, (2007).

7. M. Rafei, M.H.R. Ghoreishy, Naderi, G., "Developments of An Advanced Computer Simulation Technique for the Modeling of Rubber Curing Process", Computational Materials Science, Vol. 47, pp. 539-547, (2009).

8. Abhilash, P.M., Kannan, K. and Varkey, B., "Simulation of Curing of a Slab Rubber", Materials Science and Engineering, Vol. 168, pp. 237-241, (2010).

9. Ghosh P., Katare, S. and Caruthers, J.M., "Sulfur Vulcanization of Natural Rubber for Benzothiazole Accelerated", Rubber Chemistry and technology, Vol. 76, pp. 592-693, (2003).

10. Khor, C., Ariff, Y. Z. M., Ani, F. C., Mujeebu, M., Abdullah, M. K. and Joseph, M. A., "Three-Dimensional Numerical and Experimental Investigations on Polymer Rheology In Meso-Scale Injection Molding", International Communications in Heat and Mass Transfer, Vol. 37, pp. 131-139, (2010).

11. Leroy, E., Souid, A. and Deterre, R., "A continuous kinetic model of rubber vulcanization predicting induction and reversion", Polymer Testing, Vol. 32, pp. 575-582, (2013).

12. Hosseini, M. and Razzaghi, M., "Vulcanization kinetics of nano-silica filled styrene butadiene rubber", Polymer, Vol. 55, pp. 6426-6434, (2014).

13. Dongcheol, C., Abdul Kader, M., Baik-Hwan, C., Yang, I. and Changwoon, N., "Vulcanization kinetics of nitrile rubber/layered clay nanocomposites", Journal of Applied Polymer Science, Vol. 98, pp. 1688-1696, (2005).

14. Javadi, M., Moghiman, M., Erfanian, M.R. and Hosseini, N., "Numerical Investigation of Curing Process in Reaction Injection Molding of Rubber For Quality Improvements", Key Engineering Materials, Vol. 462,

pp. 1206-1211, (2011).

15. Bianchi, O., Fiorio, R., Martins, J.N., Zattera, A.J. and Scuracchio, C.H., "Crosslinking Kinetics of Blends of Ethylene Vinyl Acetate and Ground Tire Rubber", Journal of Elastomers and Plastics, Vol. 41, pp. 175-189, (2009).

16. Fan, R.L., Zhang, Y., Huang, C. and Gong, P., “Simulation and Verification For Sulphur Accelerated Vulcanization of Gum Natural Rubber Compound”, Rubber Chemistry and technology, Vol. 75, pp. 287-295, (2002).

17. Ghoreishy, M. H. R., Rafei, M., Naderi, G., Bakhshandeh, G. R. and Nasiri, M., "Computer Simulation of Cure Process of an Axisymmetric Rubber Article Reinforced by Metal Plates Using Extended ABAQUS Code", Iranian Journal of Polymer Science and Technology, Vol. 23, pp. 121-131, (2010).

18. Isayev, AI. and Deng, J. S., "Non Isothermal Vulcanization of Rubber Compounds", Rubber Chemistry and Technology, Vol. 61, pp. 340-361, (1988).

19. Tong, J. and Yan, X., "Non Isothermal vulcanization of rubber compounds", Journal of Reinforced Plastic and Composites , Vol. 22, pp. 983-1002, (2003).

20. Kamal, M. and Sourour, S., "Kinetics and Thermal Characterization of Thermoset cure", Polymer Engineering and Science, Vol. 13, pp. 590-599, (1973).

21. Del Coz, J. J., Diaz Garcia Nieto, P. J. and Bello Garcia, Guerrero Munoz, A., J., "Finite Volume Modeling of The Non-Isothermal Flow of a Non-Newtonian Fluid in a Rubber’s Extrusion Die", Journal of Non-Crystalline Solids, Vol. 354, pp. 5334-5336, (2008).