Comparison of regression, bee colony, and artificial neural network for predicting die filling in stamping of bipolar plates fuel cell

Document Type : Original Article

Authors

• Vahid Modanloo
• Ahmad Mashayekhi
• Behnam Akhoundi

Mechanical Engineering Department, Sirjan University of Technology, Sirjan, Iran

10.22067/jacsm.2023.84567.1205

Abstract

Increasing the depth of microchannels on metallic bipolar plates (BPPs) in PEM fuel cells leads to an increase in the efficiency. In this research, the stamping process has been applied for manufacturing of the BPPs made of commercially pure titanium with a direct parallel flow field. The effect of process parameters including die clearance, forming speed, and sheet/die friction coefficient on the filling rate and thinning of the BPPs was investigated. The required tests were designed via the response surface method (RSM), implemented by a validated finite elements (FE) model, and the desired outputs were extracted. Then, a quadratic equation was presented for predicting the filling rate based on the input parameters using the regression method. In the following, using the artificial bee colony algorithm, the coefficients of the mentioned equation were enhanced and its error was decreased almost by 53%. Finally, an artificial neural network (ANN) was used to predict the filling rate. The results demonstrated that the proposed ANN model is very effective and approximates the filling rate of the microchannel with high accuracy.

Keywords

• Titanium bipolar plates
• Forming depth
• Stamping process
• Artificial bee colony algorithm
• Artificial neural network

Main Subjects

• Forming

---

References

[1]   V. Modanloo, M. Elyasi, “Formability of Commercial Pure Titanium in Microchannel Bipolar Plates Using Warm Stamping Process”, Modares Mechanical Engineering, vol. 20, no.6, pp. 1593-1599, (2020).

[2]   H. Hassanzadeh, A. Ferdowsara and M. Barzagary, “Modeling of two phase flow in the cathode of gas diffusion layer of proton exchange membrane fuel cell”, Modares Mechanical Engineering, vol. 14, pp. 55-62, (2014).

[3]   V. Modanloo, V. Alimirzaloo, and M. Elyasi, “Investigation on forming of titanium bipolar plates using micro-stamping process,” International Journal of Engineering, vol. 33, pp. 344-349, (2020).

DOI: 10.5829/ije.2020.33.02b.20

[4]   F. A. Khatir, M. Barzegari, H. Talebi-Ghadikolaee and S. Seddighi, “Integration of design of experiment and finite element method for the study of geometrical parameters in metallic bipolar plates for PEMFCs”, International Journal of Hydrogen Energy, vol. 46, pp. 39469-39482, (2021). https://doi.org/10.1016/j.ijhydene.2021.09.161

[5]   M. M. Barzegari, F. A. Khatir, “Study of thickness distribution and dimensional accuracy of stamped metallic bipolar plates”, International Journal of Hydrogen Energy, vol. 44, pp. 31360-31371, (2019).

https://doi.org/10.1016/j.ijhydene.2019.09.225

[6]   F. A. Khatir, M. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, “Evaluation of effective parameters on stamping of metallic bipolar plates,” Procedia Engineering, vol. 183, pp. 322-329, (2017).

https://doi.org/10.1016/j.proeng.2017.04.047

[7]   M. Elyasi, H. Talebi Ghadikolaee and M. Hosseinzadeh, “Investigation of dimensional accuracy of metallic bipolar plate's micro channel in rubber pad forming process”, Modares Mechanical Engineering, vol. 15, no.12, pp461-471, (2016).

[8]   Y.-D. Kuan, C.-W. Ciou, M.-Y. Shen, C.-K. Wang, R. Z. Fitriani and C.-Y. Lee, “Bipolar plate design and fabrication using graphite reinforced composite laminate for proton exchange membrane fuel cells”, International Journal of Hydrogen Energy, vol. 46, no.31, pp. 16801-16814, (2021).

https://doi.org/10.1016/j.ijhydene.2020.08.030

[9]   C. Mathew, S. Naina Mohamed and L. S. Devanathan, “A comprehensive review of current research on various materials used for developing composite bipolar plates in polymer electrolyte membrane fuel cells”, Polymer Composites, vol. 43, no.7, pp. 4100-4114, (2022). https://doi.org/10.1002/pc.26691

 [10]        Y. Leng, P. Ming, D. Yang and C. Zhang, “Stainless steel bipolar plates for proton exchange membrane fuel cells: Materials, flow channel design and forming processes”, Journal of Power Sources, vol. 451, p. 227783, (2020). https://doi.org/10.1016/j.jpowsour.2020.227783

[11] H. Talebi-Ghadikolaee, M. Elyasi and M. J. Mirnia, “Investigation of failure during rubber pad forming of metallic bipolar plates”, Thin-Walled Structures, vol. 150, p. 106671, (2020). https://doi.org/10.1016/j.tws.2020.106671

[12] N. Mohammadtabar, M. Bakhshi-Jooybari, S. Hosseinipour and A. Gorji, “Feasibility study of a double-step hydroforming process for fabrication of fuel cell bipolar plates with slotted interdigitated serpentine flow field”, The International Journal of Advanced Manufacturing Technology, vol. 85, pp. 765-777, (2016).

[13] V. Modanloo, V. Alimirzaloo and M. Elyasi, “Multi-objective optimization of the stamping of titanium bipolar plates for fuel cell”, ADMT Journal, vol. 12, pp. 1-8, (2019).

[14] M. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, “Fabrication of metallic bipolar plates in PEM fuel cell using semi-stamp rubber forming process”, The International Journal of Advanced Manufacturing Technology, vol. 92, pp. 765-776, (2017).

[15] V. Modanloo, V. Alimirzaloo and M. Elyasi, “Optimal design of stamping process for fabrication of titanium bipolar plates using the integration of finite element and response surface methods”, Arabian Journal for Science and Engineering, vol. 45, pp. 1097-1107, (2020).

[16] M. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, “Investigation of dimensional accuracy in forming of metallic bipolar plates with serpentine flow field”, The International Journal of Advanced Manufacturing Technology, vol. 96, pp. 1045-1060, (2018).

[17] M. Elyasi, F. Ahmadi and M. Hosseinzadeh, “Investigation of lubricant effect on depth filling of metallic bipolar plates with concave and convex patterns in rubber pad forming process”, Modares Mechanical Engineering, vol. 15, no.12, pp. 450-460, (2016).

[18] S. Mahabunphachai, Ö. N. Cora and M. Koç, “Effect of manufacturing processes on formability and surface topography of proton exchange membrane fuel cell metallic bipolar plates”, Journal of Power Sources, vol. 195, no.16, pp. 5269-5277, (2010). https://doi.org/10.1016/j.jpowsour.2010.03.018

[19] J.Y. Koo, Y.P. Jeon and C.G. Kang, “Effect of stamping load variation on deformation behaviour of stainless steel thin plate with microchannel”, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 227, no.8, pp. 1121-1128, (2013). https://doi.org/10.1177/0954405412462673

[20] W. T. Park, C. K. Jin and C. G. Kang, “Improving channel depth of stainless steel bipolar plate in fuel cell using process parameters of stamping”, The International Journal of Advanced Manufacturing Technology, vol. 87, pp. 1677-1684, (2016).