Investigating the Effect of Friction Stir Welding Parameters on the Mechanical Properties of Copper Sheets under Helium Gas

Document Type : Original Article

Authors

1 Department of Materials Engineering, Faculty of Engineering, University of Gonabad, Gonabad, Iran

2 Department of Mechanical Engineering, Ilam, Iran

3 Department of Mechanical Engineering, Bu-Ali Sina University, Hamedan, Iran

4 Sama Islamshahr Boys Complex, Islamshahr, Tehran, Iran

Abstract

In this research, copper sheets with different welding conditions, including different rotational and translational speeds of the tool, as well as the number of one and two welding passes, were connected to each other by friction stir welding method. These weldings were performed under helium gas as a protective gas. Blowing helium gas on welds and welding tools prevents air from coming in contact with them and avoids the adverse effects that air can have on them. In this research, due to the softness of the copper metal and the thinness of the sheets, J-integral samples were used instead of the critical stress intensity coefficient KIC samples. This quantity was measured by making C(T) samples. The results of this study showed that due to the occurrence of recrystallization phenomenon in the stirring zone, fracture toughness and Vickers hardness can increase by 41.49% and 52.85%, respectively, compared to the base metal. The occurrence of annealing phenomenon in the heat-affected area leads to the degradation of microstructural and mechanical properties, so that the Vickers hardness, ultimate strength and fracture toughness decrease by 28.57%, 33.90% and 10.98% compared to the base metal, respectively. In addition, the research results showed that in order to obtain a better weld, it is more appropriate to perform the welding process at a lower temperature instead of two or more welding passes, so that less heat is transferred to the workpiece.

Keywords

Main Subjects

References

[1] Y. F. Sun, and H. Fujii, "Investigation of the welding parameter dependent microstructure and mechanical properties of friction stir welded pure copper," Materials Science and Engineering: A, vol. 527, no. 26, pp. 6879-6886, 2010. https://doi.org/10.1016/j.msea.2010.07.030
[2] B. Zareh, M. Bakhshi, A.H. Gorji, and S. Nourouzi, "Analysis of forming parameters in sheet hydro-forming process," Journal of Applied and Computational Sciences in Mechanics, vol. 24, no. 1, pp. 33-52, 2012. (In Persian). https://doi.org/10.22067/fum-mech.v24i1.21491
[3] G. Payganeh, Q. Malekzadeh Fard, J. Shahbazi Karami, and O. Chaeichi Siqahkal, "Experimental study and simulation of tube ydroforming process of bi-layered aluminum-copper with axial feeding," Journal of Applied and Computational Sciences in Mechanics, vol. 28, no. 2, pp. 65-84, 2017. (In Persian) https://doi.org/10.22067/fum-mech.v28i2.48455
[4] B. Murugan, and S. Kundu, "Study on microstructure, mechanical, and electrochemical behaviour of friction stir welded joints between aluminium and 304 stainless steel," Materials Research Express, vol. 6, no. 1, pp. 6016515, 2018. https://doi.org/10.1088/2053-1591/aae3c1
[5] A. Ozer, A. Sik, B. Cevik, and M. Ozer, "The effect of friction stir welding parameters on microstructure and fatigue strength of CuZn37 brass alloys," Kovove Materialy, vol. 55, pp. 107-114, 2017. DOI: 10.4149/km_2017_2107
[6] K. Praneetha, M. Apoorva, T. Prasanna Laxmi, S. Ravi Sekhar, and S. Sravan Sashank, "Experimental investigation on aluminium alloy AA6082 and AA2014 using the friction stir welding," Materials Today: Proceedings, vol. 62, no. 6, pp. 3397-3404, 2022. https://doi.org/10.1016/j.matpr.2022.04.270
[7] M. Atashparva, and M. Hamedi, "Investigating the effect of film in SSRSW of hastelloy X superalloy," Journal of Applied and Computational Sciences in Mechanics, vol. 30, no. 1, pp. 129-140, 2018. (In Persian) https://doi.org/10.22067/fum-mech.v30i1.63369
[8] P. Harisha, H. M. Nanjundaswamy, H. N. Divakar, and D. Krishnan," Tensile properties of aluminium and copper alloys friction stir welded joints," Materials Today: Proceedings, vol. 54, pp. 223-227, 2021. https://doi.org/10.1016/j.matpr.2021.08.297
[9] M. Mashayekhi, and H. Hedayati, "Effect of welding sequence and hydrotest process on welding residual stresses in stainless steel SUS304 pipes," Journal of Applied and Computational Sciences in Mechanics, vol. 22, no. 2 ,pp. 17-34, 2011. (In Persian) https://doi.org/10.22067/fum-mech.v22i2.10613
[10] F. Gao, Y. Guo, W. Yu, P. Jiang, and Zh. Liao, "Microstructure evolution of friction stir welding of Ti6321 titanium alloy based on the weld temperature below microstructure transformation temperature," Materials Characterization, vol. 177, pp. 111121, 2021. https://doi.org/10.1016/j.matchar.2021.111121
[11] A. A. E. Sidhom, S. A. R. Naga, and A. M. Kamal, "Friction stir spot welding of similar and dissimilar high density polyethylene and polypropylene sheets," Advances in Industrial and Manufacturing Engineering, vol. 4, pp. 100076, 2022. https://doi.org/10.1016/j.aime.2022.100076
[12] A. Paoletti, F. Lambiase, and A. Di Ilio, "Optimization of friction stir welding of thermoplastics," Procedia CIRP, vol. 33, pp. 562-567, 2015. https://doi.org/10.1016/j.procir.2015.06.078
[13] M. R. Ojnordy, and F. Kolahan, "Numerical analysis and experimental study on friction stir welding (Case studies on aluminum alloy and mild steel)," Modares Mechanical Engineering, vol. 18, no. 2, pp. 263-253, 2018. (In Persian) dorl.net/dor/20.1001.1.10275940.1397.18.2.19.8
 [14] H. L. Qin, H. Zhang, D. T. Sun, and Q. Y. Zhuang, "Corrosion behavior of friction-stir-welding joints of 2A14-T6 aluminum alloy," International Journal of Minerals, Metallurgy and Materials, vol. 22, pp. 627-638, 2015. https://doi.org/10.1007/s12613-015-1116-9
[15] Y. F. Sun, and H. Fujii, "The effect of SiC particles on the microstructure and mechanical properties of friction stir welded pure copper joints," Materials Science and Engineering: A, vol. 528, no. 16-17, pp. 5470-5475, 2011. https://doi.org/10.1016/j.msea.2011.03.077
[16] S. Yaghoubi, and A. Shirazi, "Mechanical properties and corrosion behavior of friction stir welded copper plates under shielding gas," International Journal of Fatigue, vol. 152, pp. 106419, 2021. https://doi.org/10.1016/j.ijfatigue.2021.106419
[17] P. Kahhal, M. Ghasemi, and M. Kashfi, "The Multi-Objective Optimization of the Friction Stir Welding using the Taguchi Design Method, the Response Surface Model and the Particle Swarm Algorithm," Scientific Journal of Aerospace Mechanics, vol. 17, no. 4, pp. 39-54, 2021. (In Persian). dor: 20.1001.1.26455323.1400.14.4.4.2
[18] "ASTM E92-17 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials, ASTM International, West Conshohocken, PA," (2016). doi: 10.1520/E0092-17
[19] "ASTM E8 / E8M-16a, Standard Test Methods for Tension Testing of Metallic Materials, ASTM International, West Conshohocken, PA," (2016). doi: 10.1520/E0008-04.
[20] "ASTM E1820 Standard Test Methods for Fracture toughness Testing of Metallic Materials, ASTM International, West Conshohocken, PA," (2016). doi: 10.1520/E1820-09.
[21] W. B. Lee, and S. B. Jung, "The joint properties of copper by friction stir welding," Materials Letters, vol. 58, no. 6, pp. 1041-1046, 2004. https://doi.org/10.1016/j.matlet.2003.08.014
[22] A. Azizi, R. V. Barenji, A. V. Barenji, and M. Hashemipour, "Microstructure and mechanical properties of friction stir welded thick pure copper plates," The International Journal of Advanced Manufacturing Technology, vol. 86, pp. 1985-1995, 2016. https://doi.org/10.1007/s00170-015
 
 
Send comment about this article
CAPTCHA Image

Files

Share

How to cite

Statistics