Formability Study in Roll Forming Process: Insights into the Influence of Process Parameters on Damage Distribution

Document Type : Original Article

Authors

1 Faculty of MecFaculty of Mechanical Engineering, University of Kashan, Kashan, Iranhanical Engineering

2 Department of Mechanical Engineering, Tarbiat Modares University, Tehran, Iran

3 Faculty of Mechanical Engineering, Qom University of Technology, Qom, Iran

4 Faculty of Mechanical Engineering, Semnan University, Semnan, Iran

Abstract

In this study, the phenomenon of ductile fracture in single-stage roll forming processes was investigated. In this regard, the fracture behavior of the 6061-T6 aluminum alloy was examined using the Modified Mohr-Coulomb fracture criterion. Subsequently, the calibration of the fracture criterion was carried out using a combined experimental-simulation approach. The roll forming process was modeled using finite element analysis, and the fracture criterion was implemented within the appropriate subroutine of the finite element simulation. According to the results, the Modified Mohr-Coulomb criterion with a 4.47% error capability could predict the onset of fracture in the single-stage roll forming process. Considering the sensitivity of the damage distribution accuracy to the stress state during the process, the effects of process parameters including thickness, bending angle, and corner radius on the triaxial stress parameter were investigated. The results indicate that these parameters do not have a significant impact on the triaxial stress parameter, and its average value remains within the range of 0.057 throughout all cases. Therefore, the fracture prediction results obtained with this criterion can be extended to other roll forming scenarios. Based on this, the influence of process parameters on damage and fracture during the roll forming process was examined. According to the results, an increase in sheet thickness and bending angle leads to an increase in damage, while an increase in the corner radius results in a reduction in damage area and a delayed occurrence of fracture during the process

Keywords

Main Subjects

References

  1. Elyasi, F. A. Khatir and M. Hosseinzadeh, "Manufacturing metallic bipolar plate fuel cells through rubber pad forming process", The International Journal of Advanced Manufacturing Technology, vol. 89, pp. 3257-3269, (2017). https://doi.org/10.1007/s00170-016-9297-6
  2. Elyasi, H. T. Ghadikolaee and M. Hosseinzadeh, "Fabrication of metallic bipolar plates in PEM fuel cell using semi-stamp rubber forming process", The International Journal of Advanced Manufacturing Technology, vol. 92, pp. 765-776, (2017). https://doi.org/10.1007/s00170-017-0206-4
  3. Modanloo, V. Alimirzaloo and M. Elyasi, "Manufacturing of titanium bipolar plates using warm stamping process", Arabian Journal for Science and Engineering, vol. 45, pp. 9661-9667, (2020). https://doi.org/10.1007/s13369-020-04870-3
  4. Talebi-Ghadikolaee, V. Modanloo, M. Elyasi and F. A. Khatir, "Multiple criteria decision support analysis for manufacturing process parameters selection of metallic bipolar plates for polymer electrolyte membrane fuel cells", Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, p. 14644207231203312, (2023). https://doi.org/10.1177/14644207231203312
  5. Seddighi, M. M. Barzegari and H. Talebi-Ghadikolaee, "Numerical-experimental investigation of using rubber blank holder on wrinkling of metallic bipolar plates formed by stamping process", International Journal of Hydrogen Energy, (2023). https://doi.org/10.1016/j.ijhydene.2023.03.172
  6. Elyasi, M. Paluch and M. Hosseinzadeh, "Predicting the bending limit of AA8112 tubes using necking criterion in manufacturing of bent tubes", The International Journal of Advanced Manufacturing Technology, vol. 88, pp. 3307-3318, (2017). https://doi.org/10.1007/s00170-016-9042-1
  7. Elyasi, M. Bakhshi-Jooybari, A. Gorji, S. Hosseinipour and S. Nourouzi, "New die design for improvement of die corner filling in hydroforming of cylindrical stepped tubes", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 223, no. 7, pp. 821-827, (2009). https://doi.org/10.1243/09544054JEM1344
  8. A. Nourmohammadi, M. Elyasi, and M. J. Mirnia, "Flexibility improvement in two-point incremental forming by implementing multi-point die," The International Journal of Advanced Manufacturing Technology, vol. 102, pp. 2933-2952, (2019). https://doi.org/10.1007/s00170-019-03307-y
  9. Hashemi, M. Hoseinpour and S. M. H. Seyedkashi, "Determination of Optimal Pressure Path in Sheet Hydroforming Process using Simulated Annealing Method", Journal Of Applied and Computational Sciences in Mechanics, vol. 28, no. 1, pp. 123-131, (2017). https://doi.org/10.22067/fum-mech.v28i1.41691.
  10. Azamirad, B. Arezoo, "Automatic determination of non-uniform blank-holder force in sheet metal forming", Journal Of Applied and Computational Sciences in Mechanics, vol. 34, no. 1, pp. 81-96, (2022). https://doi.org/10.22067/jacsm.2022.73195.1066.
  11. Hajiahmadi, H. M. Naeini, H. Talebi-Ghadikolaee, R. Safdarian and A. Zeinolabedin-Beygi, "Effect of anisotropy on spring-back of pre-punched profiles in cold roll forming process: an experimental and numerical investigation", The International Journal of Advanced Manufacturing Technology, pp. 1-14, (2023). https://doi.org/10.1007/s00170-023-12516-5
  12. Talebi-Ghadikolaee, M. M. Barzegari and S. Seddighi, "Investigation of deformation mechanics and forming limit of thin-walled metallic bipolar plates", International Journal of Hydrogen Energy, vol. 48, no. 11, pp. 4469-4491, (2023). https://doi.org/10.1016/j.ijhydene.2022.10.270
  13. Talebi-Ghadikolaee, H. Moslemi Naeini, A. H. Rabiee, A. Zeinolabedin Beygi, and S. Alexandrov, "Experimental-numerical analysis of ductile damage modeling of aluminum alloy using a hybrid approach: ductile fracture criteria and adaptive neural-fuzzy system (ANFIS)", International Journal of Modelling and Simulation, pp. 1-16, (2022). https://doi.org/10.1080/02286203.2022.2121675
  14. Ahmadi khatir, M. Elyasi, H. Talebi-Ghadikolaee, and V. Modanloo, "Experimental investigation and Numerical simulation of bending parameters on the spring back of the tube in the rotational bending process", Journal Of Applied and Computational Sciences in Mechanics, (2023).https:// doi.org/10.22067/jacsm.2023.84485.1204.
  15. Kadkhodayan, R. Akbary, "An Investigation into the Effect of Friction and Blank Holden Force on the Springblak of U-bending of an Isotropic Plates", Journal Of Applied and Computational Sciences in Mechanics, vol. 21, no. 1, pp. 115-127, 2010. https://doi.org/10.22067/fum-mech.v21i1.7715.
  16. Talebi-Ghadikolaee, H. M. Naeini, E. T. Ghadikolaee and M. J. Mirnia, "Predictive modeling of damage evolution and ductile fracture in bending process", Materials Today Communications, vol. 31, p. 103543, (2022). https://doi.org/10.1016/j.mtcomm.2022.103543
  17. Zohrabi, S. Mazdak and H. Talebi-Ghadikolaee, "Selection of Appropriate Ductile Fracture Criterion to Predict Failure of Folded Cross Section Profiles in Reshaping Process", Iranian Journal of Manufacturing Engineering, vol. 8, no. 8, pp. 24-37, (2021).
  18. Zahedi Dizajyekan, "Investigation of Fracture Mechanism in Single Point Incremental Forming of AA5052 Aluminum Alloy Using the Bao-Wierzbicki Damage Model", Journal Of Applied and Computational Sciences in Mechanics, vol. 35, no.34, pp. 63-76 (2023). https://doi.org/10.22067/jacsm.2023.81834.1180
  19. Ma, X. Yan and T. Gernay, "Ductile fracture of dual-phase steel at elevated temperatures", Engineering Structures, vol. 288, p. 116256, (2023). https://doi.org/10.1016/j.engstruct.2023.116256
  20. Yang, Y. Guo and Y. Li, "A new ductile failure criterion with stress triaxiality and Lode dependence", Engineering Fracture Mechanics, p. 109394, (2023).https://doi.org/10.1016/j.engstruct.2023.116256
  21. Lou, H. Huh, S. Lim and K. Pack, "New ductile fracture criterion for prediction of fracture forming limit diagrams of sheet metals", International Journal of Solids and Structures, vol. 49, no. 25, pp. 3605-3615, (2012). https://doi.org/10.1016/j.ijsolstr.2012.02.016
  22. J. Mirnia, M. Shamsari, "Numerical prediction of failure in single point incremental forming using a phenomenological ductile fracture criterion", Journal of Materials Processing Technology, vol. 244, pp. 17-43, (2017). https://doi.org/10.1016/j.jmatprotec.2017.01.029
  23. J. Mirnia, M. Vahdani, "Calibration of ductile fracture criterion from shear to equibiaxial tension using hydraulic bulge test", (2020). https://doi.org/10.1016/j.jmatprotec.2020.116589
  24. Zahedi, B. M. Dariani, and M. J. Mirnia, "Experimental determination and numerical prediction of necking and fracture forming limit curves of laminated Al/Cu sheets using a damage plasticity model", International Journal of Mechanical Sciences, vol. 153, pp. 341-358, (2019).https://doi.org/10.1016/j.ijmecsci.2019.02.002
  25. Zhan, Q. Hu, Z. Wang, S. Cai, and J. Chen, "The numerical method for predicting failure in single point incremental forming using a new anisotropic ductile fracture model," Procedia Manufacturing, vol. 29, pp. 45-52, (2019). https://doi.org/10.1016/j.promfg.2019.02.104
  26. B. Othmen, N. Haddar, A. Jegat, P.-Y. Manach and K. Elleuch, "Ductile fracture of AISI 304L stainless steel sheet in stretching", International Journal of Mechanical Sciences, p. 105404, (2020). https://doi.org/10.1016/j.ijmecsci.2019.105404
  27. S. Zeinali, H. M. Naeini, H. Talebi-Ghadikolaee and V. Panahizadeh, "Numerical and experimental investigation of fracture in roll forming process using Lou–Huh fracture criterion", Arabian Journal for Science and Engineering, vol. 47, no. 12, pp. 15591-15602, (2022). https://doi.org/10.1007/s13369-022-06662-3
  28. Zhao, Y. Yan, H. B. Wang and J. F. Gao, "Finite element analysis and fracture forecast of U channel flexible roll forming", Advanced Materials Research, vol. 683: Trans Tech Publ, pp. 604-607, (2013).https://doi.org/10.4028/www.scientific.net/AMR.683.604
  29.  Dadgar Asl, M. M. Sheikhi, A. Pourkamali Anaraki and M. Hosseinpour Gollo, "Experimental and Numerical Analysis of Fracture on Flexible Roll Forming Process of channel section in Aluminum 6061-T6 sheet", Modares Mechanical Engineering, vol. 16, no. 5, pp. 329-338, (2016).
  30. Wang, Y. Yan, F. Jia, and F. Han, "Investigations of fracture on DP980 steel sheet in roll forming process", Journal of Manufacturing Processes, vol. 22, pp. 177-184, (2016). https://doi.org/10.1016/j.jmapro.2016.03.008
  31. D. Deole, M. R. Barnett, and M. Weiss, "The numerical prediction of ductile fracture of martensitic steel in roll forming", International Journal of Solids and Structures, vol. 144, pp. 20-31, (2018). https://doi.org/10.1016/j.ijsolstr.2018.04.011
  32. Talebi-Ghadikolaee, H. M. Naeini, M. J. Mirnia, M. A. Mirzai, H. Gorji and S. Alexandrov, "Ductile fracture prediction of AA6061-T6 in roll forming process", Mechanics of Materials, vol. 148, p. 103498, )2020(. https://doi.org/10.1016/j.mechmat.2020.103498
  33. Talebi-Ghadikolaee, H. M. Naeini, M. J. Mirnia, M. A. Mirzai, S. Alexandrov and M. S. Zeinali, "Modeling of ductile damage evolution in roll forming of U-channel sections", Journal of Materials Processing Technology, vol. 283, p. 116690, (2020). https://doi.org/10.1016/j.jmatprotec.2020.116690
  34. Talebi-Ghadikolaee, H. M. Naeini, M. J. Mirnia, M. A. Mirzai, H. Gorji, and S. Alexandrov, "Fracture analysis on U-bending of AA6061 aluminum alloy sheet using phenomenological ductile fracture criteria," Thin-Walled Structures, vol. 148, p. 106566, (2020).https://doi.org/10.1016/j.tws.2019.106566
  35. Talebi-Ghadikolaee, H. Moslemi Naeini, M. Mirnia, M. Mirzai, H. Gorji and S. Alexandrov, "Study of the effect of calibration procedure on the accuracy of the phenomenological ductile fracture criteria in sheet metal forming", Journal of Solid and Fluid Mechanics, vol. 10, no. 1, pp. 1-16, (2020).
  36. Talebi-Ghadikolaee, H. Moslemi Naeini, M. J. Mirnia, M. A. Mirzai, S. Alexandrov and H. Gorji, "Experimental and numerical investigation of failure during bending of AA6061 aluminum alloy sheet using the modified Mohr-Coulomb fracture criterion", The International Journal of Advanced Manufacturing Technology, vol. 105, pp. 5217-5237, (2019). https://doi.org/10.1007/s00170-019-04549-6
  37. Zou, N. Zhou, Y. Peng, D. Tang and D. Li, "Numerical simulation of the roll forming process of aluminum folded micro-channel tube", Journal of Physics: Conference Series, vol. 734, no. 3: IOP Publishing, p. 032016, (2016). https://doi.org/10.1088/1742-6596/734/3/032016
Send comment about this article
CAPTCHA Image

Files

Share

How to cite

Statistics