Journal Of Applied and Computational Sciences in Mechanics

Journal Of Applied and Computational Sciences in Mechanics

Effect of microtube addition on thermal and hydrodynamic behavior of microchannel heatsink for nanofluid Flow

Document Type : Original Article

Authors
Akram Jahanbakhshi 1
Afshin Ahmadi Nadooshan 2
Morteza Bayareh 2
1 Engineering Faculty- Shahrekord University, Shahrekord
2 Engineering Faculty, Shahrekord University,Shahrekord, Iran
10.22067/jacsm.2022.75344.1100
Abstract
In the present study, two geometries of microtube and microchannel are used simultaneously in a heatsink. The aim is to improve the performance of micro heatsink in cooling digital processors. ANSYS FLUENT software is employed to solve the governing equations. The second-order upwind method is utilized to solve the momentum equation and the SIMPLE method is employed for coupling the velocity and pressure fields. The results show that the fluid flow temperature changes less along with the micro heatsink by increasing the Reynolds number due to the high flow rate. Also, the surface temperature of the processor decreases significantly by enhancing the concentration of nanoparticles and improving the heat transfer performance. Hence, at Re =700 and a volume fraction of 0.5%, the average outlet temperature of the system is 316.1 K. It is equal to 319.03 K for a volume fraction of 1%. The addition of microtubes also causes a significant increment in the overall thermal efficiency of the system. For example, at Re = 300, the heat transfer coefficient for the base fluid flow with microtubes is approximately 58.4% higher than that for the system without microtubes. At Re =700 and 1500, this enhancement is 63.3% and 50.9%, respectively. This indicates that the presence of microtubes improves the performance of the heatsink and the access of heat transfer in different parts of the equipment to the cooling fluid flow. It reduces the thermal resistance of far points of the processor, leading to more heat absorption from the CPU surface.
Keywords
Microtube
thermal and hydrodynamic behavior
Microchannel
Heat Sink
Nanofluid
Subjects
  1. Sohel, M. R., Saidur, R., Sabri M. F., Kamalisarvestani, M., Elias, M. M., Ijam, A., "Investigating the Heat Transfer Performance and Thermophysical Properties of Nanofluids in a Circular Micro-Channel", International Communications in Heat and Mass Transfer, Vol. 42, Pp. 75-81, (2013).
  2. Kim, S. M., Mudawar, I., "Review of Databases and Predictive Methods for Heat Transfer in Condensing and Boiling Mini/Micro-Channel Flows", International Journal of Heat and Mass Transfer., Vol. 77, Pp. 627-652, (2014).
  3. Dehghan, M., Mahmoudi, Y., Valipour, M. S, Saedodin, S.,"Combined Conduction–Convection–Radiation Heat Transfer of Slip Flow inside a Micro-Channel Filled with a Porous Material", Transport in Porous Media, Vol. 108, Pp. 413-436, (2015).
  4. Keepaiboon, C., Wongwises, S., "Two-Phase Flow Patterns and Heat Transfer Characteristics of R134a Refrigerant during Flow Boiling in a Single Rectangular Micro-Channel", Experimental Thermal and Fluid Science, Vol. 66, Pp. 36- 45, (2015).
  5. Gamrat, G., Favre-Marinet, M., Asendrych, D., "Conduction and Entrance Effects on Laminar Liquid Flow and Heat Transfer in Rectangular Microchannels", International Journal of Heat and Mass Transfer, Vol. 48, No. 14, Pp. 2943-2954, (2005).
  6. Bar-Cohen, A., "Gen-3 Thermal Management Technology: Role of Microchannels and Nanostructures in an Embedded Cooling Paradigm", Journal of Nanotechnology in Engineering and Medicine, Vol. 4, No. 2: 020907 (3 pages), (2013).
  7. Colgan, E. G., Furman, B., Gaynes, M., Graham, W.S., LaBianca, N.C., Magerlein, J.H., Polastre, R.J., Rothwell, M.B., Bezama, R.J., Choudhary, R., Marston, K.C., "A Practical Implementation of Silicon Microchannel Coolers for High Power Chips", IEEE Transactions on Components and Packaging Technologies., Vol. 30, No. 2, Pp. 218-225, (2007).
  8. Lee, J., Mudawar, I., "Low-Temperature Two-Phase Microchannel Cooling for High-Heat-Flux Thermal Management of Defense Electronics", IEEE Transactions on Components and Packaging Technologies. 32, No. 2, Pp. 453-465, (2009).
  9. Solovitz, S.A., Stevanovic, L.D., Beaupre, R.A., "Micro-Channel Thermal Management of High Power Devices", In Twenty-First Annual IEEE Applied Power Electronics Conference and Exposition. APEC'06, Mar 19 (2006).
  10. Tuckerman, D.B., Pease, R.F., "High-Performance Heat Sinking for VLSI", IEEE Electron Device Letters. Vol. 2, No. 5, Pp. 126-129., (1981).
  11. Azizi, Z., Alamdari, A., Malayeri, M.R., "Convective Heat Transfer of Cu–Water Nanofluid in a Cylindrical Microchannel Heat Sink", Energy Conversion and Management,Vol. 101, Pp. 515-524, (2015).
  12. Ho, C.J., Wei, L.C., Li, Z.W., "An Experimental Investigation of Forced Convective Cooling Performance of a Microchannel Heat Sink with Al2O3/Water Nanofluid", Applied Thermal Engineering. 30, No. 2-3, Pp. 96-103, (2010).
  13. Chen, C.H., Ding, C.Y., "Study on the Thermal Behavior and Cooling Performance of a Nanofluid-Cooled Microchannel Heat Sink", International Journal of Thermal Sciences. Vol. 50, No. 3, Pp. 378-384., (2011).
  14. Lelea, D., "The Performance Evaluation of Al2O3/Water Nanofluid Flow and Heat Transfer in Microchannel Heat Sink", International Journal of Heat and Mass Transfer, 54, No. 17-18, Pp. 3891-3899, (2011).
  15. Pourmehran, O., Rahimi-Gorji, M., Hatami, M., Sahebi, S.A., Domairry, G., "Numerical Optimization of Microchannel Heat Sink (MCHS) Performance Cooled by KKL Based Nanofluids in Saturated Porous Medium", Journal of the Taiwan Institute of Chemical Engineers, Vol. 55, Pp. 49-68, (2015).
  16. Chein, R., Huang, G., "Analysis of Microchannel Heat Sink Performance Using Nanofluids", Applied Thermal Engineering. 25, No.17-18, Pp. 3104-3114, (2005).
  17. Li, J., Kleinstreuer, C., "Thermal Performance of Nanofluid Flow in Microchannels", International Journal of Heat and Fluid Flow, Vol. 29, No. 4, Pp. 1221-1232, (2008).
  18. Ghasemi, S.E., Ranjbar, A.A., Hosseini, M.J., "Thermal and Hydrodynamic Characteristics of Water-Based Suspensions of Al2O3 Nanoparticles in a Novel Minichannel Heat Sink", Journal of Molecular Liquids, 230, Pp. 550-556., (2017).
  19. Tafarroj, M.M., Mahian, O., Kasaeian, A., Sakamatapan, K., Dalkilic, A.S., Wongwises, S., "Artificial Neural Network Modeling of Nanofluid Flow in a Microchannel Heat Sink Using Experimental Data", International Communications in Heat and Mass Transfer. 86, Pp. 25-31., (2017).
  20. Rashidi, M.M., Ganji, D.D., Shahmohamadi, H., "Variational Iteration Method for Two-Dimensional Steady Slip Flow in Micro-Channels", Archive of Applied Mechanics, 81, No. 11, Pp. 1597-1605, (2011).
  21. Hasan, M.I., Rageb, A.A., Yaghoubi, M., Homayoni, H., "Influence of Channel Geometry on the Performance of a Counter Flow Microchannel Heat Exchanger", International Journal of Thermal Sciences, Vol. 48, No. 8, Pp. 1607-1618, (2009).
  22. Sarafraz, M.M., Hormozi, F.J., "Intensification of Forced Convection Heat Transfer Using Biological Nanofluid in a Double-Pipe Heat Exchanger", Experimental Thermal and Fluid Science, Vol. 66, Pp. 279-289, (2015).
  23. Al-Rashed, A.A., Shahsavar, A., Rasooli, O., Moghimi, M.A., Karimipour, A., Tran, M.D., "Numerical Assessment into the Hydrothermal and Entropy Generation Characteristics of Biological Water-Silver Nano-Fluid in a Wavy Walled Microchannel Heat Sink", International Communications in Heat and Mass Transfer, Vol. 104, Pp. 118-126, (2019).
Send comment about this article
Enter Name.
Enter a valid email address.
Enter a vaid affiliation.
Enter comments (At leaset 10 words)
CAPTCHA Image
Enter Security Code Correctly.