Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction

Talebi, Mansour; Nabati, Siamak

doi:10.22067/jacsm.2021.71640.1046

Effect of Vanes Angles on the Flow around Fuel Rods and the Induced Vibrations by Analyzing Solid-Fluid Interaction

Document Type : Original Article

Authors

Mansour Talebi ¹

Siamak Nabati ²

¹ Nuclear Science and Technology Research Institute

² Islamic Azad University, Isfahan, Iran

10.22067/jacsm.2021.71640.1046

Abstract

In the nuclear fuel assembly, the mixing vanes are solid components which are attached to the spacer grid. These vanes would increase heat transfer rate from the fuel wall. The force induced by flow may expose the vanes to excessive stress and bending, which in turn, it impairs the mixing vanes. In order to improve the heat transfer rate and decrease the vibrational forces, vanes are usually positioned at a certain angle regarding to the flow axis. This study investigates displacement of vanes in three angles of 65, 70 and 75 degrees for a specific geometry using the fluid-solid interaction method. First, the fluid flow is solved using a Finite Volume Method (FVM) solver and the forces exposed by the flow to the vanes are estimated. Next, the displacement of the vanes due to the applied forces is calculated by the Finite Element Method (FEM). Comparison between calculated pressure drop in this study and experimental result show a difference less than 10%. The maximum pressure drop is occurred when the vanes have 65° angle. The most turbulence intensity is obtained at the angle of 75°. Also, according to the frequency estimation, it was observed that with increasing frequency the displacement's amplitude would decrease.

Keywords

Mixing Vanes

Fuel Assembly

Fluid Solid Interaction

Induced vibrations

Subjects

Fluid mechanics

Lee, S. G., Lee, G. S., Lee, H. S., Park, J. H. and Jung, T.Y., "Full-scale ship collision, grounding and sinking simulation using highly advanced M&S system of FSI analysis technique", Procedia Engineering, Vol. 173, pp. 1507–1514, (2017).
Bogaers, A. E. J., Kok, S., Reddy, B. D. and Franz, T., "An evaluation of quasi-Newton methods for application to FSI problems involving free surface flow and solid body contact", Computers & Structures, Vol. 173, pp. 71–83, (2016).
Long, T., Hu, D., Yang, G. and Wan, D., "A particle-element contact algorithm incorporated into the coupling methods of FEM-ISPH and FEM-WCSPH for FSI problems", Ocean Engineering, Vol. 123, pp. 154–163, (2016).
Fourey, G., Hermange, C., Touze, D. L. and Oger, G, "An efficient FSI coupling strategy between smoothed particle hydrodynamics and finite element methods", Computer Physics Communications, Vol. 217, pp. 66–81, (2017).
Franci, A., Oñate, E. and Carbonell, J. M., "Unified Lagrangian formulation for solid and fluid mechanics and FSI problems", Computer Methods in Applied Mechanics and Engineering, Vol. 298, pp.
520–547, (2016).
Xu, Q., Chen, J., Zhang, C., Li, J. and Zhao, C., "Dynamic analysis of AP1000 shield building considering fluid and structure interaction effects", Nuclear Engineering and Technology, Vol. 48, pp. 246–258, (2106).
Daogang, L., Aiguo, L., ChaoHao, S., Junjie, D., Yang, H. and Qingyu, X., "Experimental investigation on fluid–structure-coupled dynamic characteristics of the double fuel assemblies in a fast reactor", Nuclear Engineering and Design, Vol. 255, pp. 180–184, (2013).
Trivedi, C., "A review on fluid structure interaction in hydraulic turbines: A focus on hydrodynamic damping", Engineering Failure Analysis, Vol. 77, pp. 1–22, (2017).
Ricciardi, G., Bellizzi, S., Collard, B. and Cochelin, B., "Fluid-structure interaction in a 3-by-3 reduced-scale fuel assembly network", Science and Technology of Nuclear installations, Vol. 2010, pp. 1-8, Doi:10.1155/2010/517471, Article ID, 517471, (2010).
Xiong, J., Qu, W., Zhang, T., Chai, X., Liu, X. and Yang, Y., "Experimental investigation on split-mixing-vane forced mixing in pressurized water reactor fuel assembly", Annals of Nuclear Energy, Vol. 143, 107450, (2020).
Dhurandhar, S. K., Sinha, S. L. and Verma, S. K., "Effects of Mixing Vane Spacer on Flow and Thermal Behavior of Fluid in Fuel Channels of Nuclear Reactors—A Review", Nuclear Technology, Vol. 206, pp. 663-696, (2020).
ANSYS, Inc. ANSYS WORKBENCH Guide, (2020).
ANSYS, Inc. ANSYS FLUENT Theory Guide, (2020).
Smith, S. T. and Fox, R.O., "A term-by-term direct numerical simulation validation study of the multi-environment conditional probability-density-function model for turbulent reacting flows", Physics of Fluids, Vol. 19, 85102, doi:10.1063/1.275769, (2007).
Asgari, M., Talebi, M. and Abi, M.R., "Numerical Simulation of Pressure Loss and Heat Transfer in Road Bundle Fuel Assembly with Spacer Grids", of Nuclear Sci. and Tech, Vol. 64, pp. 67-76, (2013) (In Persian).
Karouta, Z., Gu, C. Y. and Schölin, B., "3-D flow analyses for design of nuclear fuel spacer", Proceedings of the 7^th International Meeting on Nuclear Reactor Thermal-Hydraulics NURETH-7. Sessions, pp.17-24, (1995).