Journal Of Applied and Computational Sciences in Mechanics

Journal Of Applied and Computational Sciences in Mechanics

Simulation of fluid flow in a heat exchanger with elastic intermediate separator at different working conditions

Document Type : Original Article

Authors
Seyed Esmael Razavi 1
Tohid Adibi 2
1 Department of Mechanical Engineering, University of Tabriz, Tabriz, Iran
2 Department of Mechanical Engineering, University of Bonab, Bonab, Iran
10.22067/jacsm.2021.56517.0
Abstract
In this work, a plate heat exchanger with an inconsistent flow is investigated in different working conditions. Four different models in laminar and turbulent flows with rigid and elastic plates at different Reynolds numbers have been studied, and the effect of the separator plate elasticity on the heat transfer rate and the efficiency of the heat exchanger has been investigated. A sinusoidal profile is used at the entrance to the cold passage. The results of this study showed that the elasticity of the intermediate plate in both laminar and turbulent flow has raised the heat transfer rate. Of course, in cases where the middle plane was elastic, the friction coefficient increased relative to the rigid plate. The efficiency of the heat exchanger is defined and is obtained for the heat exchanger to consider both heat transfer rate and pressure drop. Results showed that in most cases, the efficiency of the heat exchanger with elastic separator is more than one. The results showed that the maximum efficiency is 5.2 which was observed in Re=3000 and the minimum efficiency is 0.9 which occurs in Re=200.
Keywords
Heat exchanger
Elastic plate
Nusselt number
sinusoid velocity
Reynolds number
Subjects
  1. Adibi, T., Adibi, O., Razavi, S. E., "A Characteristic-based Solution of Forced and Free Convection in Closed Domains with Emphasis on Various Fluids", International Journal of Engineering, 32(11), pp. 1689-1695 (2019).
  2. Adibi, T., Razavi, S. E., Adibi, O., "A Characteristic-based Numerical Simulation of Water-titanium Dioxide Nano-fluid in Closed Domains", International Journal of Engineering,33(1), pp. 158-163 (2020).
  3. Razavi, S. E., Adibi, T., Faramarzi, S., "Impact of inclined and perforated baffles on the laminar thermo-flow behavior in rectangular channels", SN Applied Sciences, 2(2), pp. 284 (2020).
  4. Adibi, T., Razavi, S. E., Adibi, O., et al., "The response of nano-ceramic doped fluids in heat convection models: A characteristics-based numerical approach", Scientia Iranica, 28(5), pp. 2671-2683 (2021).
  5. Ji, J., Zhang, J., Gao, R., et al., "Numerical Research on Vibration-Enhanced Heat Transfer of Elastic Scroll Tube Bundle", Journal of Thermophysics and Heat Transfer, 1-8 (2021).
  6. Dinesh Kumar, S., Chandramohan, D., Purushothaman, K., et al., "Optimal hydraulic and thermal constrain for plate heat exchanger using multi objective wale optimization", Materials Today: Proceedings, 21, pp. 876-881 (2020).
  7. Sadeghi, H. M., Babayan, M., Chamkha, , "Investigation of using multi-layer PCMs in the tubular heat exchanger with periodic heat transfer boundary condition", International Journal of Heat and Mass Transfer, Vol. 147, pp. 118970 (2020).
  8. Adibi, T., Razavi, S. E., Abbasi Tabrizi, E., "Numerical Simulation of the Heat-Fluid Flow Behavior Around the Cylinder with the Controller Wire", Journal Of Applied and Computational Sciences in Mechanics, 31(2), pp. 105-126 (2020).
  9. Jafar Kazemi, f., Ahangari, a. r., Rahimi, b., "Analysis of Heat and Mass Transfer in an Open Cooling Tower", Journal Of Applied and Computational Sciences in Mechanics, 21(1), pp. 59-74 (2010).
  10. Nazari, M., Gerivani, H., Tafakkor, S., "Conjugate Heat Transfer in Closed Cavity with Porous Blocks", Journal Of Applied and Computational Sciences in Mechanics, 29(1), pp. 111-121 (2018).
  11. Khan, W. A., Yovanovich, M. M., "Analytical Modeling of Fluid Flow and Heat Transfer in Microchannel/Nanochannel Heat Sinks", Journal of Thermophysics and Heat Transfer, 22(3), pp. 352-359, (2008).
  12. Al-Nimr, M. A., Maqableh, M., Khadrawi, A. F., et al., "Fully developed thermal behaviors for parallel flow microchannel heat exchanger", International Communications in Heat and Mass Transfer, 36(4). pp. 385-390 (2009).
  13. Hasan, M. I., Rageb, A. A., Yaghoubi, M., et al., "Influence of channel geometry on the performance of a counter flow microchannel heat exchanger", International Journal of Thermal Sciences,48(8) pp. 1607-1618 (2009).
  14. Vera, M., Liñán, A., "Laminar counterflow parallel-plate heat exchangers: Exact and approximate solutions", International Journal of Heat and Mass Transfer, 53(21), pp. 4885-4898 (2010).
  15. Sheik Ismail, L., Velraj, R., Ranganayakulu, C., "Studies on pumping power in terms of pressure drop and heat transfer characteristics of compact plate-fin heat exchangers—A review", Renewable and Sustainable Energy Reviews,14(1), pp. 478-485 (2010).
  16. Zhan, C., Duan, Z., Zhao, X., et al., "Comparative study of the performance of the M-cycle counter-flow and cross-flow heat exchangers for indirect evaporative cooling – Paving the path toward sustainable cooling of buildings", Energy,36(12), pp. 6790-6805 (2011).
  17. Sammeta, H., Ponnusamy, K., Majid, M. A., et al., "Effectiveness charts for counter flow corrugated plate heat exchanger", Simulation Modelling Practice and Theory,19(2), pp. 777-784 (2011).
  18. Sui, Y., Teo, C. J., Lee, P. S., "Direct numerical simulation of fluid flow and heat transfer in periodic wavy channels with rectangular cross-sections", International Journal of Heat and Mass Transfer,55(1), pp. 73-88 (2012).
  19. Faizal, M., Ahmed, M. R., "Experimental studies on a corrugated plate heat exchanger for small temperature difference applications", Experimental Thermal and Fluid Science,36, pp. 242-248, (2012).
  20. Zhang, G.-m., Li, G.-q., Li, W., et al., "Particulate fouling and composite fouling assessment in corrugated plate heat exchangers", International Journal of Heat and Mass Transfer, 60, pp. 263-273 (2013).
  21. Bell, I. H., Quoilin, , Georges, E., et al., "A generalized moving-boundary algorithm to predict the heat transfer rate of counterflow heat exchangers for any phase configuration", Applied Thermal Engineering, Vol.79, pp. 192-201 (2015).
  22. Sarraf, K., Launay, S., Tadrist, L., "Complex 3D-flow analysis and corrugation angle effect in plate heat exchangers", International Journal of Thermal Sciences, 94, pp. 126-138 (2015).
  23. Wajs, J., Mikielewicz, D., "Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger", Applied Thermal Engineering, 93, pp. 1337-1346 (2016).
  24. Aminuddin, M., Zubair, S. M., "Analytical solutions to counter-flow heat exchanger subjected to external heat flux and axial conduction", International Journal of Refrigeration,74, pp. 22-37 (2017).
  25. Imran, M., Pambudi, N. A., Farooq, M., "Thermal and hydraulic optimization of plate heat exchanger using multi objective genetic algorithm", Case Studies in Thermal Engineering,10, pp. 570-578 (2017).
  26. Lu, W., Zhang, T., Yang, M., et al., "Analytical solutions of force convective heat transfer in plate heat exchangers partially filled with metal foams", International Journal of Heat and Mass Transfer,110, pp. 476-481 (2017).
  27. Sheikholeslami, M., Haq, R.-u., Shafee, A., et al., "Heat transfer simulation of heat storage unit with nanoparticles and fins through a heat exchanger", International Journal of Heat and Mass Transfer,135, pp. 470-478 (2019).
  28. Razavi, S. E., Adibi, T., "A novel multidimensional characteristic modeling of incompressible convective heat transfer", Journal of Applied Fluid Mechanics,9(4), pp. 1135-1146 (2016).
  29. Adibi, T., Razavi, S. E., "A new characteristic approach for incompressible thermo-flow in Cartesian and non-Cartesian grids", International Journal for Numerical Methods in Fluids,79(8), pp. 371-393 (2015).
  30. Adibi, T., "Three-dimensional characteristic approach for incompressible thermo-flows and influence of artificial compressibility parameter", Journal of Computational & Applied Research in Mechanical Engineering (JCARME), 8(2), pp. 223-234 (2019).
  31. Jia, R., Hu, J., Xiong, X., Modeling of a Counter Flow Plate Fin Heat Exchanger, COMSOL Boston Conference, (2014).
Send comment about this article
Enter Name.
Enter a valid email address.
Enter a vaid affiliation.
Enter comments (At leaset 10 words)
CAPTCHA Image
Enter Security Code Correctly.