Investigating the Effect of Phase Change Materials on Energy Consumption in Lightweight Prefabricated Relief Buildings

Document Type : Original Article

Authors

• ALI Amiri ¹
• Amir Yarinezhad ²

¹ Mechanical Engineering Department, Engineering Faculty, Razi University, Kermanshah, Iran.

² Architectural Engineering Department, Engineering Faculty, Razi University, Kermanshah, Iran.

10.22067/jacsm.2022.78503.1136

Abstract

In this research, the role of Phase Change Materials (PCM) in energy saving in lightweight prefabricated buildings is studied. For this purpose, a typical building in Kermanshah, Iran is simulated in DesignBuilder software. A split unit is used as air conditioning system. The annual energy consumption of the building in the reference state is 2577.27 kWh. The implementation of the InfiniteRPCM21C was investigated in all directions including each individual wall, ceiling, four walls simultaneously and the entire building envelope. The southern wall is the best option among the walls with 12.14% energy saving. From an economic point of view, this wall has the best performance as well by saving 2.08 kWh/kgPCM. Implementation on the entire envelope increases savings up to 37.2%. Although this is not an economical case, but it reduces the need for energy to almost zero in four months of the year. By examining the PCM in different layers of the wall, it was found that in all directions, the inner surface of the wall leads to the greatest energy savings. Also, taking account the PCM thickness in the range of 5 to 25 mm showed that the smaller the thickness, the greater the savings per unit mass of the PCM. Therefore, thicknesses more than 20 mm are not recommended. Finally, the effect of the PCM melting point in the range of 18 to 29 degrees Celsius was investigated and it was found that the maximum energy saving is obtained at the melting point of 21 degrees Celsius.

Keywords

• Phase change materials
• PCM
• Energy saving
• Thermal comfort
• Prefabricated building
• DesignBuilder

Main Subjects

• Renewable energy

---

References

• Kuznik, J. Virgone, "Experimental assessment of a phase change material for wall building use", Applied Energy, vol. 86, no. 10, Pp. 2038-2046, 2009.
• Li, Z. Wu, and J. Tan, "Heat storage properties of the cement mortar incorporated with composite phase change material", Applied Energy, vol. 103, Pp. 393-399, 2013.
• S. Dehkordi, M. Afrand, "Energy-saving owing to using PCM into buildings: Considering of hot and cold climate region", Sustainable Energy Technologies and Assessments, vol. 52, Pp. 102-112, 2022.
• Jia, L. Bo, M. Lingyong, W. Hui, L. Dong, and W. Yiran, "Energy saving performance optimization and regional adaptability of prefabricated buildings with PCM in different climates", Case Studies in Thermal Engineering, vol. 26, Pp. 101-164, 2021.
• Liu, Z. Li, Y. Teng, and L. Dai, "A dynamic simulation study on the sustainability of prefabricated buildings", Sustainable Cities and Society,vol. 77, Pp. 103551, 2022.
• Shen, Y. Yu., J. Hou, Q. Wang, L. Zhang, and X. Meng, "The Testing Research on Prefabricated Building Indoor Thermal Environment of Earthquake Disaster Region", Procedia Engineering, vol. 205, Pp. 453-460, 2017.{Carey, 1998 #8}
• Wang, L. Wang, E. Long, and S. Deng, "An experimental study on the indoor thermal environment in prefabricated houses in the subtropics", Energy and Buildings, vol. 127, Pp. 529-539, 2016.
• Tetlow, L. Simon, S. YeeLiew, B. Hewakandamby, D. Mack, W. Thielemans, and S. Riffata, "Cellulosic-crystals as a fumed-silica substitute in vacuum insulated panel technology used in building construction and retrofit applications", Energy and Buildings, vol. 156, Pp. 187-196, 2017.
• Evola, L. Marletta, and F. Sicurella, "A methodology for investigating the effectiveness of PCM wallboards for summer thermal comfort in buildings", Building and Environment, vol. 59, Pp. 517-527, 2013.
• M. Khudhair, M.M. Farid, "A review on energy conservation in building applications with thermal storage by latent heat using phase change materials", Energy Conversion and Management, vol. 45, no. 2, Pp. 263-275, 2004.
• Konuklu, M. Ostry, H. Paksoy, and P. Charvat, "Review on using microencapsulated phase change materials (PCM) in building applications", Energy and Buildings, vol. 106, Pp. 134-155, 2015.
• Pielichowska, K. Pielichowski, "Phase change materials for thermal energy storage", Progress in Materials Science, vol. 65, Pp. 67-123, 2014.
• Mandilaras, M. Stamatiadou, D. Katsourinis, G. Zannis, and M. Founti, "Experimental thermal characterization of a Mediterranean residential building with PCM gypsum board walls", Building and Environment, vol. 61, Pp. 93-103, 2013.
• Bianco, V. Serra, S. Fantucci, M. Dutto, and M. Massolino, "Thermal insulating plaster as a solution for refurbishing historic building envelopes: First experimental results", Energy and Buildings, vol. 95, Pp. 86-91, 2015.
• F. Cabeza, C. Castellón, M. nogués, M. Medrano, R. Leppers, and O. Zubillaga, "Use of microencapsulated PCM in concrete walls for energy savings", Energy and Buildings, vol. 39, no. 2, Pp. 113-119, 2007.
• Barreneche, A. Fernández, M. Niubó, J. Chimenos, F. Espiell, M. Segarra, C. Solé, and L. Cabeza, "Development and characterization of new shape-stabilized phase change material (PCM)-Polymer including electrical arc furnace dust (EAFD), for acoustic and thermal comfort in buildings", Energy and Buildings, vol. 61, Pp. 210-214, 2013.
• Vicente, T. Silva, "Brick masonry walls with PCM macrocapsules: An experimental approach", Applied Thermal Engineering, vol. 67, no. 1, Pp. 24-34, 2014.
• G. Jeong, J. Jeon, J. Seo, J. HunLee, and S. Kim, "Performance evaluation of the microencapsulated PCM for wood-based flooring application", Energy Conversion and Management, vol. 64, Pp. 516-521, 2012.
• Marin, M. Saffari, A. Gracia, X. Zhu, M.M. Farid, L. Cabeza, and S. Ushak, "Energy savings due to the use of PCM for relocatable lightweight buildings passive heating and cooling in different weather conditions", Energy and Buildings, vol. 129, Pp. 274-283, 2016.{Carey, 1998 #8}
• Sonnick, L. Erlbeck, K. Schlachter, J. Strischakov, T. Mai, C. Mayer, K. Jakob, H. Nirschl, and M. Rädle, "Temperature stabilization using salt hydrate storage system to achieve thermal comfort in prefabricated wooden houses", Energy and Buildings, vol. 164, Pp. 48-60, 2018.
• Zhu, Y. Yang, S. Chen, and Y. Sun, "Numerical study on the thermal performance of lightweight temporary building integrated with phase change materials", Applied Thermal Engineering, vol. 138, Pp. 35-47, 2018.
• Fateh, D. Borelli, H. Weinläder, and F. Devia, "Cardinal orientation and melting temperature effects for PCM-enhanced light-walls in different climates", Sustainable Cities and Society, vol. 51, Pp. 101766, 2019.
• Wang, H. Xiao, D. Shiming, L. Enshen, and N. Jianlei, "An experimental study on applying PCMs to disaster-relief prefabricated temporary houses for improving internal thermal environment in summer", Energy and Buildings, vol. 179, Pp. 301-310, 2018.
• Wang, S. Deng, J. Niu, and E. Long, "A numerical study on optimizing the designs of applying PCMs to a disaster-relief prefabricated temporary-house (PTH) to improve its summer daytime indoor thermal environment", Energy, vol. 181, Pp. 239-249, 2019.
• Mohseni, W. Tang, "Parametric analysis and optimisation of energy efficiency of a lightweight building integrated with different configurations and types of PCM", Renewable Energy, vol. 168, Pp. 865-877, 2021.
• a. Liu, J. Hou, X. Meng, and B.J. Dewancker, "A numerical study on the effect of phase-change material (PCM) parameters on the thermal performance of lightweight building walls", Case Studies in Construction Materials, vol. 15, Pp. e00758, 2021.
• A. Kishore, M.V.A. Bianchi, C. Booten, J. Vidal, and R. Jackson, "Parametric and sensitivity analysis of a PCM-integrated wall for optimal thermal load modulation in lightweight buildings", Applied Thermal Engineering, vol. 187, Pp. 116568, 2021.
• Available: https://www.ladybug.tools/epwmap. [Accessed Nov. 22, 2021].
• Schober, C. Boer, and L.A. Schwarte, "Correlation Coefficients: Appropriate Use and Interpretation", Anesth Analg, vol. 126, no. 5, Pp. 1763-1768, 2018.