Experimental Investigation on Process Parameters Effects in Laser Forming of Closed-cell Aluminium Foam Sheets

Document Type : Original Article

Authors

1 Tarbiat Modares University

2 Shahid Rajaee Teacher Training University

3 Imam Khomeini International University

Abstract

In a laser forming process, the temperature gradient across the sheet thickness produces the final bending angle. Metallic foams cannot be formed by any mechanical processes due to occurrence of failure during deformation. In this article, closed-cell aluminium foams are irradiated by a laser beam. Experiments are carried out by varying laser power, scan velocity and the number of scan passes to specify their effect on the bending angle. Design of experiment with the response surface methodology and analysis of variance are utilized to analyze parameter effects. At last, an equation is derived for prediction of bending angle.

Keywords


1. Zhang, X., "Laser-assisted High Precision Bending and its Applications", Mechanical Engineering; Industrial Engineering Board, Dissertation/Thesis No. 3154677, Indiana, (2004).
2. Geiger, M. and Vollertsen, F., "The Mechanisms of Laser Forming", CIRP Annals - Manufacturing Technology, Vol. 42, 301-304, (1993).
3. Shichun, W. and Jinsong, Z., "An experimental study of laser bending for sheet metals", Journal of Materials Processing Technology, Vol. 110, pp. 160-163, (2001).
4. Guan, Y., Sun, S., Zhao, G. and Luan, Y., "Influence of material properties on the laser-forming process of sheet metals", Journal of Materials Processing Technology, Vol. 167, pp. 124-131, (2005).
5. Che Jamil, M.S., Sheikh, M.A. and Li, L., "A study of the effect of laser beam geometries on laser bending of sheet metal by buckling mechanism", Optics & Laser Technology, Vol. 43, pp. 183-193, (2011).
6. Edwardson, S.P., Abed, E., Bartkowiak, K., Dearden, G. and Watkins, K.G., "Geometrical influences on multi-pass laser forming", Journal of Physics D: Applied Physics, Vol. 39, pp. 382, (2006).
7. Cheng, J. and Lawrence Yao, Y., "Cooling Effects in Multiscan Laser Forming", Journal of Manufacturing Processes, Vol. 3, pp. 60-72, (2001).
8. Cheng, P., Fan, Y., Zhang, J., Yao, Y.L., Mika, D.P., Zhang, W., Graham, M., Marte, J. and Jones, M., "Laser Forming of Varying Thickness Plate—Part I: Process Analysis", Journal of Manufacturing Science and Engineering, Vol. 128, pp. 634-641, (2005).
9. Hoseinpour Gollo, M., Mahdavian, S.M. and Moslemi Naeini, H., "Statistical analysis of parameter effects on bending angle in laser forming process by pulsed Nd:YAG laser", Optics & Laser Technology, Vol. 43, pp. 475-482, (2011).
10. Shen, H. and Yao, Z., "Study on mechanical properties after laser forming", Optics and Lasers in Engineering, Vol. 47, pp. 111-117, (2009).
11. Wu, D., Zhang, Q., Ma, G., Guo, Y. and Guo, D., "Laser bending of brittle materials", Optics and Lasers in Engineering, Vol. 48, pp. 405-410, (2010).
12. Shi, Y., Liu, Y., Yi, P. and Hu, J., "Effect of different heating methods on deformation of metal plate under upsetting mechanism in laser forming", Optics & Laser Technology, Vol. 44, pp. 486-491, (2012).
13. Guan, Y., Zhang, H., Liu, J. and Sun, S., "Laser micro-bending process based on the characteristic of the laser polarization", Journal of Materials Processing Technology, Vol. 212, pp. 662-671, (2012).
14. Ghadiri Zahrani, E. and Marasi, A., "Experimental investigation of edge effect and longitudinal distortion in laser bending process", Optics & Laser Technology, Vol. 45, pp. 301-307, (2013).
15. Maji, K., Pratihar, D.K. and Nath, A.K., "Experimental investigations and statistical analysis of pulsed laser bending of AISI 304 stainless steel sheet", Optics & Laser Technology, Vol. 49, pp. 18-27, (2013).
16. Safari, M. and Farzin, M., "Experimental and numerical investigation of laser bending of tailor machined blanks", Optics & Laser Technology, Vol. 48, pp. 513-522, (2013).
17. Merklein, M., Hennige, T. and Geiger, M., "Laser forming of aluminium and aluminium alloys — microstructural investigation", Journal of Materials Processing Technology, Vol. 115, pp. 159-165, (2001).
18. Labeas, G.N., "Development of a local three-dimensional numerical simulation model for the laser forming process of aluminium components", Journal of Materials Processing Technology, Vol. 207, pp. 248-257, (2008).
19. Qin, Y., Chen, Y., Ni, X., Shen, Z., Bi, J. and Zhang X., "Axisymmetric numerical simulation of plastic damage in aluminum alloy induced by long pulsed laser", Optics and Lasers in Engineering, Vol. 48, pp. 361-367, (2010).
20. Knupfer, S.M. and Moore, A.J., "The effects of laser forming on the mechanical and metallurgical properties of low carbon steel and aluminium alloy samples", Materials Science and Engineering: A, Vol. 527, pp. 4347-4359, (2010).
21. Roohi, A.H., Gollo, M.H. and Naeini, H.M., "External force-assisted laser forming process for gaining high bending angles", Journal of Manufacturing Processes, Vol. 14, pp. 269-276, (2012).
22. Banhart, J. "Manufacture, Characterization and Application of Cellular Metals and Metal Foam", Progress in Materials Science, Vol. 46, pp. 559-632, (2001).
23. Ashby, M.F., Evans, A.G., Fleck, N.A., Gibson, L.J., Hutchinson, J.W. and Wadley, H.N.G, "Metal Foams: A Design Guide", Woburn: Butterworth-Heinemann publication. Inc., Woburn, pp. 1-5, (2000).
24. Quadrini, F., Guglielmotti, A., Squeo, E.A. and Tagliaferri, V., "Laser Forming of Open-cell Aluminium Foams, Journal of Materials Processing Technology", Vol. 210, pp. 1517-1522, (2010).
25. Design Expert. Software 7.0.0, Stat-Ease, Inc. 2005, Help Section.
CAPTCHA Image